User manual CASIO EXILIM EX-ZR10

[. . . ] E Digital Camera User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ To go to "Getting the Most Out of Dynamic Photo" click here! Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] · Make sure that the camera is turned off before plugging in or unplugging the cable. Check the user documentation that comes with the TV for information about requirements before plugging into or unplugging from the TV. 2. Turn on the TV and select its video input mode. If the TV has more than one video input, select the one where the camera is connected. 105 Viewing Snapshots and Movies 3. Press [p] (PLAY) to turn on the camera. This will cause an image to appear on the TV screen, without anything appearing on the camera's monitor screen. · Pressing [ON/OFF] (Power) or [r] (REC) will not turn on the camera while the AV cable is connected. · You also can change the aspect ratio of the screen and the video output system (page 158). 4. Now you can display images and play back movies as you normally do. IMPORTANT! · Before connecting to a TV to display images, be sure to configure the camera's [r] (REC) and [p] (PLAY) buttons for "Power On" or "Power On/Off" (page 157). When you first start displaying images, set the TV volume control at a relatively low level and then adjust it as required. NOTE · Audio is stereo. · Some TVs may not be able to output images and/or audio correctly. · All icons and indicators that appear on the monitor screen also appear on the TV screen. You can use [8] (DISP) to change the display contents. 106 Viewing Snapshots and Movies Viewing High-quality Movies on a Hi-Vision Television Use a commercially available HDMI cable to connect the camera to the TV. For information about playback, see the procedure starting from step 2 under "Viewing Snapshots and Movies on a TV Screen" on page 105. · Use a commercially available HDMI cable that is marked with the logo shown to the right. HDMI connector HDMI cable (commercially available) HDMI output (Mini) HDMI input HDMI mini connector Terminal cover IMPORTANT! · Output to a TV is not supported while the camera is in the REC mode. NOTE · Use a HDMI cable that with a plug that is compatible with the camera's HDMI mini connector on one end, and a plug that is compatible with your TV's HDMI connector on the other end. · Proper image and/or audio output and other operations may not be possible with some devices. · Connecting the camera to the HDMI connector of another device can damage both the camera and the other device. · Make sure that the camera is turned off before plugging in or unplugging the cable. Check the user documentation that comes with the TV for information about requirements before plugging into or unplugging from the TV. · When cables are connected to both the USB/AV port and the HDMI output connector, the HDMI output connector connection is given priority. · Disconnect the HDMI cable when you are not using HDMI output. The camera's monitor screen may not operate normally while the HDMI cable is connected. · Some TVs may not be able to output images and/or audio correctly. When you first start displaying images, set the TV volume control at a relatively low level and then adjust it as required. 107 Viewing Snapshots and Movies . Selecting the HDMI Terminal Output Method (HDMI Output) Procedure [MENU] * Set Up Tab * HDMI Output Use this setting to select the digital signal format when connecting to a TV with an HDMI cable. Auto 1080i 480p 576p This setting will cause the format to change automatically in accordance with the connected TV. 1080i format output* 480p format output 576p format output * 1080i corresponds to 1080 60i, but not 1080 50i. [. . . ] Remove the memory card from the camera (if one is loaded). You will not be able to access the built-in subjects while a memory card is loaded in the camera. 2. In the REC mode, compose the image and press the shutter button to shoot a standard snapshot. You will insert the built-in subject into the snapshot you shoot here. Step 2: Create the Dynamic Photo image. Now simply insert a built-in subject into the snapshot or movie you shot in step 1 to create your own original Dynamic Photo image. 1. Perform the following operation on the camera [MENU] * PLAY tab * "Dynamic Photo". 3. Use [4] and [6] to select the background image you want and then press [SET]. Select the image you want to use as the background. [. . . ]