User manual CASIO EXILIM EX-H20G

[. . . ] E Digital Camera User's Guide Thank you for purchasing this CASIO product. · Before using it, be sure to read the precautions contained in this User's Guide. · Keep the User's Guide in a safe place for future reference. · For the most up-to-date information about this product, visit the official EXILIM Website at http://www. exilim. com/ To go to "Getting the Most Out of Dynamic Photo" click here! 1 Unpacking As you unpack your camera, check to make sure that all items shown below are included. [. . . ] Use [8] and [2] to select the setting you want and then press [SET]. Enables image cursor movement. Holding down [BS] and tilting the camera approximately 20 degrees away from you will move the cursor upwards. Tilting the camera towards you will move the cursor downwards. On Off Disables image cursor movement. NOTE · The current "Move Cursor" setting is ignored while "Off" is selected for the "GPS" setting (page 92). B 104 Using the Hybrid-GPS Using Other Map Data (MAP Tab Menu) This section explains the menu items that are used when performing operations and configuring settings in the MAP mode. For information about menu operations, see page 58. Saving Position Information (Save Log) Procedure [ý] (MAP) * [MENU] * MAP Tab * Save Log You can use this procedure to save position information from different locations and different times. While "On" is selected for the "Save Log" setting, the following information is saved in camera memory for 14 days as positioning log data. ­ Date (year, month, day) and time (hour, minute) ­ Latitude and longitude ­ Altitude (When GPS positioning is performed. ) ­ Positioning method and positioning accuracy · The current "Save Log" setting is ignored while "Off" is selected for the "GPS" setting (page 92). · Formatting the camera's built-in memory deletes all positioning log data stored there. IMPORTANT! · Note that in China it is against the law to accumulate a log of position information without the permission of government authorities. Be sure to select "Off" for the "Save Log" setting if you are using the camera in China and do not have such permission. Tracking Your Movements on a Map (Show Log) Procedure [ý] (MAP) * [MENU] * MAP Tab * Show Log You can track you movements by displaying positioning log data on a map. Selecting "On" for the "Show Log" setting causes saved positioning log data to be displayed on the map. Specifying the Display Period of Tracks (Log Period) Procedure [ý] (MAP) * [MENU] * MAP Tab * Log Period This setting lets you specify how many past days of track data should be displayed on map. C 105 Using the Hybrid-GPS Saving All Positioning Log Data in Camera Memory to a Memory Card (Output Log) Use the procedure below to convert all of the positioning log data currently in camera memory to a KML file (extension: . kml) and save it to a memory card. 1. 4. Turn off the camera and load the memory card to which you want to save the file. Use [8] and [2] to select "Save" and then press [SET]. The message "Saving data. Please wait. . . " will appear, indicating that the positioning log data is being written to the memory card. NOTE · A new KML file is created in memory each day. The dates used for the date and time entries within a KML file are based on the current time setting of the camera when the "Output Log" operation is performed. · KML files are stored in a KML folder, which is located inside the memory card's DCIM folder. · The Output Log function cannot be used if there is no memory card loaded in the camera, if the memory card loaded in the camera is full, or if the camera's battery cover is open. · You can import the KML files to Google Earth or some other map software and track your movements on your computer screen. Enabling Movement of the Image Cursor (Move Cursor) Procedure [ý] (MAP) * [MENU] * MAP Tab * Move Cursor See page 104 for details. Adjusting the Accuracy of the Direction Sensor (Direction Adj) The camera's built-in direction sensor may not operate normally if there is a source of magnetism nearby. If you feel that direction measurements are not correct, perform the following procedure. 1. On the "MAP" tab, select "Direction Adj". B 106 Using the Hybrid-GPS 3. Taking care not to drop the camera, slowly swing it around in a figure eight for about 10 seconds. Use the wrist of the hand that is holding the camera to move in a way that forms a figure eight. This will correct for the magnetism and adjust direction sensor accuracy. The message "Completed normally. " will appear to let you know that accuracy adjustment is complete, and the map screen will return to the display. · Performing this adjustment near a train, an automobile, a magnet, or a concentration of metal can result in incorrect adjustment. · Direction sensor adjustment is not supported while "Off" is selected for the "GPS" setting (page 92). Converting Location Information of Images from Another Source for Playback on This Camera (Update Info) You can use this procedure to convert position information (latitude and longitude) accompanying an image recorded on another manufacturer's camera so it can be played back in the MAP mode of this camera. 1. [. . . ] Remove the memory card from the camera (if one is loaded). You will not be able to access the built-in subjects while a memory card is loaded in the camera. 2. In the REC mode, compose the image and press the shutter button to shoot a standard snapshot. You will insert the built-in subject into the snapshot you shoot here. Step 2: Create the Dynamic Photo image. Now simply insert a built-in subject into the snapshot or movie you shot in step 1 to create your own original Dynamic Photo image. 1. Perform the following operation on the camera [MENU] * PLAY tab * "Dynamic Photo". 3. Use [4] and [6] to select the background image you want and then press [SET]. Select the image you want to use as the background. [. . . ]