User manual CASIO DV-01

[. . . ] E-9 Projector Features and Main Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10 General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-10 Remote Controller General Guide . . . . . . . . . . . E-13 Getting Ready . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-14 Setting Up the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . E-17 Connecting to a Component Video Output Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-18 Connecting a USB Device to the Projector (USB Port Equipped Models Only) . . . . . . . . . . . . [. . . ] Note that connection only to an analog component video output terminal is supported. Connection to a digital output terminal is not supported. E-18 Getting Ready Connecting a USB Device to the Projector (USB Port Equipped Models Only) English If you have an XJ-SC215/XJ-S37/DV-01/XJ-S57 model projector, you can connect any of the following USB devices to the projector's USB port. USB Memory Device* You can transfer image and movie data from your computer to a USB memory device and take it along with you for projection with the projector. The projector comes with software that converts Microsoft PowerPoint sheets to images, which you can then store to a USB memory device. This means you can include PowerPoint data in your presentations without having to lug a computer along everywhere you go. makes no guarantees concerning the operation of any particular USB memory device. Wireless Adapter (YW-2) Connecting a YW-2 Wireless Adapter to your projector makes it possible to wirelessly transmit computer images to the projector. Document Camera (YC-400/YC-430 Multi PJ Camera System) You can connect the YC-400/YC-430 Multi PJ Camera System directly to the USB port of the projector and project images of documents without going through a computer. For details about connecting these USB devices to the projector and procedures you need to perform to project images from a USB device, see "USB Function Guide" on the bundled CD-ROM. E-19 Getting Ready Turning On the Projector Before performing any of the operations in this section, make sure you first set up the projector and connect to an output device. AC Power Cord Precautions Use the AC power cord that comes with the projector. Make sure that you use a power source with the same voltage as that specified for the projector. Do not share the outlet supplying power to the projector with other devices. This greatly reduces the amount of time it takes until you are ready to start projecting. Note, however, that the actual startup sequence (Standby State Power On Warm Up Projection Starts) that the projector performs is the same, regardless of whether Direct Power On is enabled or disabled. The only difference is what triggers the sequence (plugging in or pressing the [ ] (power) key). For details about the startup sequence that the projector performs when you plug it into a power source, see "To turn on the projector" on page E-20. For details about configuring the Direct Power On setting, see "Direct Power On" under "Option Settings 1 Main Menu" in the "User's Guide". E-21 English Getting Ready Turning Off the Projector When you turn off the projector, the lamp goes out and the projector goes into a cool down state. Note that you will not be able to turn the projector back on again while it is cooling down. Take care when moving the projector or otherwise handling it after use. See "Precaution when Handling the Projector after Use" (page E-8) for more information. Make sure that the projector is cooled down sufficiently before storing it. To turn off the projector 1. Press the [ ] (power) key. This causes the confirmation message "Do you want to turn off the projector?" to appear in the center of the projection screen. If you do not turn off the projector the confirmation message will disappear automatically after about 10 seconds. The confirmation message will also disappear if you press [ESC] key. 2. To turn off the projector, press the [ confirmation message. ] (power) key again in response to the This causes the projector lamp to go out and stops projection. [. . . ] If the TEMP or LAMP indicator remains flashing or lit, it means some type of error has occurred. See "Error Indicators and Warning Messages" under "Indicators". The connected computer or video device may not be turned on, or it may not be outputting a video signal. Make sure the connected computer or video device is turned on, and perform the required operation on it to output a video signal. [. . . ]