User manual CASIO DR-210HD

[. . . ] If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. [. . . ] 0 to 127 (*default setting depends on the tone) 6-D Vibrato Waveform (WvFrm) This item is for selecting the waveform when applying vibrato to notes. You can select from among the following waveforms. Original (Org*) 7-C Acoustic Resonance Send (AReso) Specifies how much of the signal from the sound source is sent to acoustic resonance. 0 to 127 (*default setting depends on the tone) INT INT 7-D DSP ON/OFF (DSP) Switches DSP for each zone on or off. OFF, ON* ­­ Saw Down (SDw) INT Sine (Sin) Pulse 1:3 (P13) Triangle (Tri) Pulse 2:2 (P22) Saw Up (SUp) Pulse 3:1 (P31) The DSP of this Digital Piano can be used simultaneously for up to two parts. Each part ("Sound Source Configuration", page E-5) has a DSP priority, which determines which of the two parts that have DSP turned on should have the DSP effect applied. The following shows the priorities assigned to each part. Priority Part Number Part 1 Part 3 Part 2 Part 4 Part 17 to 48 Part Name Upper1 Lower1 Upper2 Lower2 Song01 to Song16, Ext01 to Ext16 * "Org" is the initial default setting for all tones. The actual default waveform type depends on the tone. 1 2 3 4 5 To apply a DSP to one or two lower priority parts (Lower2, for example), turn off DSP ON/OFF for the higher priority parts (Upper1, Lower1, Upper2). E-32 Editing Zone Parameters Control Settings If you are using multiple zones for keyboard play and you want to disable pedal and other controller operations for a particular zone, turn off the settings described in this section for that zone. 8-A Pedal Enables and disables pedal operations. OFF, ON* INT / EXT 8-B Bender (Bend) Enables and disables the do (PITCH BEND) wheel operations. OFF, ON* INT / EXT 8-C Assignable 1 (Asgn1) Enables and disables the 8 (ASSIGNABLE 1) button operations. OFF, ON* INT / EXT 8-D Assignable 2 (Asgn2) Enables and disables the 9 (ASSIGNABLE 2) button operations. OFF, ON* INT / EXT E-33 English Using Registration Memory MASTER CONTROL CARD PLAYER Normally, before playing something you need to set up the Digital Piano by configuring a number of different settings, including layer and split on/off, a tone selection for each zone, equalizer settings, and DSP settings. 5. Use the bt (w, q) buttons to specify the two-digit number you want to append to the name of the file. · The message "Replace?" will appear if a file with the same name already exists. If you want to replace the existing file with the one you are saving, press bt (YES). Press bt (NO) to return to the screen in step 4 of this procedure without saving. To save registration memory bank data to a file 1. Depending on where you want to save the data file, perform one of the steps shown below. Perform this operation: Remove the SD card from the Digital Piano's card slot. Insert the SD card into the Digital Piano's card slot. 6. To exit the LOAD/SAVE mode, press the cs (EXIT) button. If you are saving the file here: Internal area SD card NOTE 2. While holding down the bs (FUNCTION) button, press the bl (LOAD/SAVE) button. · This enters the LOAD/SAVE mode. · A registration memory bank data file saved to an SD card will be placed in the MUSICDAT folder. The MUSICDAT folder is created automatically when you format the memory card on the Digital Piano (page E-46). Note that load, delete, and rename operations cannot be performed on files that are not inside the MUSICDAT folder, or on files in folders that are inside the MUSICDAT folder. Keep this restriction in mind whenever handling SD card files with your computer. E-36 Using Registration Memory To recall registration memory bank data from a file 7. If the file is located here: Internal area SD card Perform this operation: Remove the SD card from the Digital Piano's card slot. Insert the SD card into the Digital Piano's card slot. file into the bank(s) and exits the LOAD/SAVE mode. 2. If you are recalling a file that contains data for a single bank, use the bt (w, q) buttons to scroll through the bank numbers (1 through 8) until the one to which you want to recall the data is displayed. · If you are recalling a file that contains data for all banks, you can skip this step. 4. 5. While holding down the bs (FUNCTION) button, press the bl (LOAD/SAVE) button. · This enters the LOAD/SAVE mode. Depending on the type of operation you want to perform, use the ct (u) and dk (i) buttons to display one of the screens shown below. To recall a file that contains data for a single bank To recall a file that contains data for all banks 6. Use the bt (w, q) buttons to display the file that contains the data you want to recall, and then press the dl (ENTER) button. · This will cause the message "Replace?" to appear. [. . . ] 4 : Wet Level (0 to 127) Adjusts the level of the effect sound. 10: 3-Phase Chorus 14: Distortion This is a 3-phase chorus effect using two LFOs with different sine wave rates. Parameter Value Ranges: 0 : Rate 1 (Fast LFO State) (0 to 127) Adjusts the rate of LFO 1. 4 : Wet Level (0 to 127) Adjusts the level of the effect sound. This effect provides Distortion + Amp Simulator. Parameter Value Ranges: 0 : Gain (0 to 127) Adjusts the input signal gain. [. . . ]