User manual CASIO DQR-200

[. . . ] 9 °C/ °F button Press this button to toggle the temperature units between Celsius and Fahrenheit. 0 RE-SYNC button Press this button to re-synchronize the timing of the main unit and the sub-unit. · · · · Inside, among buildings, or near neon signs Inside a vehicle Near refrigerators or other household appliances, near office equipment, mobile phones or wireless LAN devices. Near a Near high-tension construction site, power lines airport, or other sources of electrical noise, underground or in tunnels, near railroads, highways, or radio stations with interfering frequencies. [. . . ] Because of this, such factors as changes in the reflectivity of the ionosphere, as well as movement of the ionosphere to higher altitudes due to seasonal atmosaheric changes or the time of day may change the reception range of the signal and make reception temporarily impossible. · Reception is best when the back of the clock is facing toward 500 km Mainflingen. Note, however, that moving the clock while the time calibration signal receive operation is taking place will make stable reception impossible. · Think of the clock as acting like a TV or radio when it is receiving the calibration signal. When receiving indoors, move to a location as near as possible to a window. Proper signal reception can be difficult or even impossible under the conditions listed below. Manual Receive Important! · Do not perform any button or switch operation while a signal receive operation is in progress. · The time calibration signal includes both Standard Time and Daylight Saving Time (summer time) data. · The DST indicator appears on the display when Daylight Saving Time (summer time) data is received. 2 Operation Guide DQR-200 USING THE ALARM Setting the Time and Date Manually · When using the clock in an area that is outside of the range of the transmitter in Mainflingen or in an area where signal reception is impossible for some reason, you need to manually adjust the time as required. Press the SET button (3) to cycle through the setting screens as shown below. Normal Timekeeping Screen The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm Mode selector (5) to select the snooze alarm feature. Setting the Alarm Time Use the Alarm Time Set buttons (2) to set the alarm time. Pressing the Alarm Time Set buttons (2) causes the alarm time to appear in place of the date on the display. Press to change the alarm time setting (+). SET UP (+) WAVE °C/ TEMP. CLEAR MAX/MIN °F RESET DOWN (--) NC Press to change the alarm time setting (--). RE-SY · Holding down + or ­ changes the digits at high speed. Year Setting Screen 12-hour/24-hour Timekeeping Screen Turning the Alarm On and Off Use the Alarm Mode selector (5) on the side of the clock to turn the alarm on and off, and to select the snooze feature. Alarm Mode selector SNZ Description The alarm sounds at the preset time for one minute, and seven more times every five minutes thereafter. Even if you stop the alarm sound by pressing the SNOOZE/LIGHT button (1), the alarm operation is performed again five minutes later. · The indicator flashes on the display to indicate that the snooze feature is activated. The alarm sounds at the preset time for one minute. ( Month and Day Setting Screen Time Setting Screen ) ) ALM ON ( 2. While the screen you want is on the display, use the Alarm Time Set buttons (2) to change the digits that are flashing. ALM OFF The alarm does not sound. · The alarm time appears in place of the date on the display whenever the Alarm Mode selector (5) is set to ON or SNZ. · The light also turns on for the first four seconds that the alarm sounds. · The alarm sound changes over four levels as it sounds. Press + to increase the flashing digits. SET UP (+) WAVE °C/ TEMP. CLEAR MAX/MIN °F RESET DOWN (--) NC Press -- to decrease the flashing digits. Stopping the Alarm RE-SY · When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on, the alarm will sound again in about five minutes. [. . . ] · Be sure to load the batteries with their positive (+) and negative (­) ends facing correctly. · Never mix old and new batteries, or batteries of different brands. · Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto your skin. · Replace the batteries at least once a year, even if the current batteries are working properly. [. . . ]