User manual CASIO CW-L300

[. . . ] E CW-L300 User's Guide · We recommend that you print on a disc* before you record anything on it. Printing on a disc that already has data recorded on it can cause the data to become corrupted. shall not be held liable for any loss or corruption of data on discs arising through the use of this printer. Be sure to read the Safety Precautions contained in this manual before trying to use the printer for the first time, and always keep this manual on hand for future reference. RJA514733-10 GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U. S. A. [. . . ] You can also use the procedures in this section to override the Auto Fit feature and specify the character sizes you want to use. 7. There are two ways to specify the character size: · Specifying the size of a string of characters · Specifying the size of text lines Important!· Note that the character size values that you specify do not indicate absolute sizes, but rather multipliers. A size of "2×3" for example, specifies double the normal height and three times the normal width. Specifying the Size of a String of Characters You can specify the size in the range of 1×1 to 5×8 for a string of characters. Note that the maximum vertical size you can specify depends on the width of the tape you are using. For more information, see the "Tape Width and the Number of Lines and Character Sizes" on page 72. 1×1 2×3 4×4 5×6 · Note that how a character size specification affects text depends on whether the text is vertical or horizontal. 1×2 (Horizontal) 1×2 (Vertical) 31 E To specify the size of a string of characters Example: To change the size of "No Smoking" in the text "No Smoking here!" to 1×3 × 1. With and to select CHARACTER, and then press SET. This indicates the character size at the current cursor position. Character Size Mark: This mark indicates the point from which a character size specification is applied. Auto Fit Mark: This mark is inserted automatically by the printer to indicate that the text to the right of it will be adjusted automatically. · The character size mark and auto fit mark appear on the display only. · To delete a character size mark, move the cursor to the mark and then press DEL. · Deleting a character size mark causes the text to the right of it to assume the size of the next character size to the left. Deleting the last character size mark causes the size of the text to be set by the printer automatically in accordance with the width of the tape being used and the number of text lines. · Note that a character size specification applies up to the end of the current block. A size specification does not span multiple blocks. 1×3 character size Auto Fit Character Size: the highlighting located at the HEIGHT value, use and to change the value. · The printer will beep and not accept your input if you try to input a value that is not allowed. Press · If you specified the HEIGHT value by pressing a number key, the highlighting will move the WIDTH value automatically. 6. Use and to change the WIDTH value, and then press SET. · Here we will change the value to 3. and to move the cursor to the first character of the string to which you want to apply the size setting, and then press SET. Use and to move the cursor to the last character of the string to which you want to apply the size setting, and then press SET. · Here we will select "No Smoking". Character Size Auto Fit Mark Character Size Mark E 32 Specifying the Size of Text Lines You can specify the size of text lines by selecting a format as shown below. Number of Lines Format 24 or 18mm Wide 12mm Wide 9mm Wide Number of Lines Format 24 or 18mm Wide 12mm Wide 9mm Wide 3 A 1 A B C D E 2 A B C D E F 1×1 2×2 3×3 4×4 5 × 5* 1×1 1×1 1×1 2×2 2×2 1×1 2×2 2×2 1×1 3 × 3* 3 × 3* 1×1 1×1 2×2 3 × 3* ­ ­ ­ ­ ­ ­ ­ ­ 1×1 2 × 2* ­ ­ ­ D ­ ­ ­ ­ ­ ­ C B 1×1 1×1 1×1 1×1 1×1 2 × 2* 1×1 2 × 2* 1×1 2 × 2* 1×1 1×1 ­ ­ ­ ­ ­ ­ ­ ­ Smaller when the label includes a frame. · The size of text lines cannot be specified in the case of 6mm wide tape. [. . . ] Replace the ink ribbon cassette · The disc is not inserted properly into the printer. · The name you are trying to assign to data is already being used by previously stored data. Input a different name THIS IS THE WRONG TYPE OF TAPE CARTRIDGE! PRINT ERROR!NO INK RIBBON! Startup Guide, page 11 Startup Guide, page 20 54 · The cassette cover is not closed completely. [. . . ]