User manual CASIO CTK-7000

[. . . ] E USER'S GUIDE Please keep all information for future reference. Safety Precautions Before trying to use the keyboard, be sure to read the separate "Safety Precautions". CTK7000/WK7500E1B NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · An asterisk (*) next to a song area number indicates that there is already data recorded in that area. 5. Use the dial or R-14 (­, +) buttons to specify the song area number you want to copy to. 6. Press the R-16 (ENTER) button. · If the copy destination song area does not contain recorded data, the copy operation is performed immediately. · If the copy destination song area already contains recorded data, the confirmation message shown below appears asking if you want to overwrite the existing data. · You can select "All" here to clear all songs. 4. In response to the "Sure?" message that appears, press the R-14 (YES) button to clear or the R-14 (NO) button to cancel. To copy a song from one area to another 1. Perform the procedure under "To start a song editor operation" on page E-81 to display the song editor menu. Press the R-14 (YES) button to perform the copy operation and overwrite the existing song or the R-14 (NO) button to cancel. 2. Use the R-17 (t, y) buttons to move the 0 to "Copy" and then press the R-16 (ENTER) button. · This displays the "Copy Song" screen. At this time the thick brackets (%) will be located at the "Copy" setting. 3. Use the dial or R-14 (­, +) buttons to specify the song area number you want to copy from. E-82 Using the Song Sequencer To delete one or more measures from a song To insert blank measures into a song 1. Perform the procedure under "To start a song editor operation" on page E-81 to display the song editor menu. 1. Perform the procedure under "To start a song editor operation" on page E-81 to display the song editor menu. 2. Use the R-17 (t, y) buttons to move the 0 to "DeleteMeas. " and then press the R-16 (ENTER) button. · This causes "Delete Measure" screen to appear. At this time the thick brackets (%) will be located at the "Measure" setting. 2. Use the R-17 (t, y) buttons to move the 0 to "InsertMeas. " and then press the R-16 (ENTER) button. · This causes "Insert Measure" screen to appear. At this time the thick brackets (%) will be located at the "Measure" setting. 3. Use the dial or R-14 (­, +) buttons to specify the song measure you want to delete. 3. Use the dial or R-14 (­, +) buttons to specify the song measure number from which you want the insert to start. 4. Press the R-17 (y) button to move the thick brackets (%) to "Size". 4. Press the R-17 (y) button to move the thick brackets (%) to "Size". 5. Use the dial or R-14 (­, +) buttons to specify the number of measures you want to insert. · For example, specifying 002 for "Measure" and 003 for "Size" will insert three blank measures in front of song measure 2. 6. After everything is the way you want, press the R-16 (ENTER) button. 5. Use the dial or R-14 (­, +) buttons to specify the number of measures you want to delete. 7. [. . . ] 4 :Noise2 Level (0, 1, 2, 3, 4, 5) Adjusts the level of Noise Generator 2. 5 :Noise2 Density (0, 1, 2, 3, 4, 5) Adjusts the frequency of Noise Generator 2. Raising the noise level while a note is not sounding will cause noise to sound, even if there is no input signal. Dual Type DSP Parameters Dual type DSPs are configured by combining two different single type DSPs. Use the procedure below to determine what parameters that can be configured for each dual type DSP, and the operation, and setting ranges of dual type DSPs. [. . . ]