User manual CASIO CTK-495

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Important! Please note the following important information before using this product. [. . . ] If you want to record with a rhythm, press the INTRO/ENDING 1/2 or VARIATION/FILL-IN 1/2. · When recording starts, the REC indicator flashes on the display. After a few moments the indicator stops flashing, and remains on the display. E-50 707A-E-052A Song Memory Function 5. Play something on the keyboard. · You can also record Auto Accompaniment chords by selecting the applicable mode with the MODE button. See "Track 1 Contents After Real-time Recording". Mixer Mode Settings Channel 1 Mixer parameters (page E-36) are automatically recorded to Track 1. Press the START/STOP button to end recording when you are finish playing. · If you make a mistake while recording, you can stop the record operation and begin over again from step 1, or you can use the editing function (page E-58) to make corrections. Memory Capacity The keyboard has memory for approximately 10, 000 notes. · The measure number and note number flash on the display whenever remaining memory is less than 100 notes. · Recording automatically stops (and auto-accompaniment and rhythm stops playing if they are being used) whenever memory becomes full. · Initially, nothing is stored in song memory. · Using real-time recording to record to a track that already contains recorded data replaces the previous recording with the new one. Track 1 Contents After Real-time Recording In addition to keyboard notes and accompaniment chords, the following data is also recorded to Track 1 during real-time recording. · Tone number · Rhythm number · INTRO/ENDING 1 button, INTRO/ENDING 2 button, VARIATION/FILL-IN 1 button, VARIATION/FILL-IN 2 button, SYNCHRO/FILL-IN NEXT button operations · Pedal operations (option) The following data is recorded in the header whenever you start a recording of a track. · Mixer settings of other tracks · Effect type · Accompaniment volume · Reverb Level · Chorus Level · DSP Hold On/Off · Mixer Hold On/Off Memory Data Storage · Whenever you make a new recording, anything previously stored in memory is replaced. Make the following settings. · Rhythm number · MODE button 3. Press the CHORD/TR1 button, which is one of the SONG MEMORY TRACK buttons, to select Track1. · When recording starts, the REC indicator flashes on the display. After a few moments the indicator stops flashing, and remains on the display. 4. Play a chord. · Use the chord play method that is specified by the current MODE setting (FINGERED, CASIO CHORD, etc. ). · When the accompaniment mode is set to NORMAL, specify the chord using the root input keyboard and chord type input keyboard. See "Specifying Chords in the Normal Mode" on page E-54 for details. · Use the procedure under "Correcting Mistakes While Step Recording" on page E-57 to correct input mistakes you make during step recording. · You can add on to a track that already contains recorded data by selecting that track in step 3 of the above procedure. Doing so automatically locates the step recording start point at the first beat immediately following the previously recorded data. · Inputting "0" as the chord length in steps 5 and 6 of the above procedure specifies a rest, but the rest is not reflected in the accompaniment contents when the accompaniment is played. Track 1 Contents After Step Recording In addition to chords, the following data is also recorded to Track 1 during step recording. · Rhythm number · INTRO/ENDING 1 button, INTRO/ENDING 2 button, VARIATION/FILL-IN 1 button, VARIATION/FILL-IN 2 button, SYNCHRO/FILL-IN NEXT button operations Ch o r d 1 2 1 2 Chord name Measure, beat, and clock at current location* * 96 clocks = 1 beat · You can also use number buttons 1 through 7, and button 9 to specify the button release timing for the VARIATION/FILLIN 1, VARIATION/FILL-IN 2, and SYNCHRO/FILL-IN NEXT buttons. For more information, see "Specifying the Length of a Note" on page E-54. [. . . ] See "Returning the keyboard to its initial factory defaults" on page E-77 for details. · La lista de arriba muestra la configuración predeterminada de fábrica. Los números de sonido del grupo de sonidos indicados más abajo serán diferentes de los indicados en esta lista, si se han almacenado sonidos originales en la memoria del teclado (página S-42). · Sonidos de usuario (números de sonidos 700 a 799)*1 · Sonidos de usuario con ondas (números de sonido 800 a 819)*2 · Ajustes de batería de usuario con ondas (números de sonido 900 a 903)*3 · Sonidos de usuario de órgano con Drawbar (números de sonido 100 a 199)*4 *1 El ajuste predeterminado de fábrica es sonidos avanzados 000 a 099. La reinicialización del sistema (página S-70) hace que se restablezcan los ajustes de fábrica. [. . . ]