User manual CASIO CPS-7

[. . . ] Microsoft, Windows, Windows Vista, and PowerPoint are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC. Adobe and Reader are registered trademarks of Adobe Systems Incorporated. XGA is a registered trademark of IBM Corporation of the United States. [. . . ] Never leave the lens cover attached while the projector is in use. Blocking the vents Never allow the vents to become blocked. Doing so causes internal heat build up, which creates the risk of fire and breakdown of the projector. Touching the projector while it is hot creates the risk of burn injury. · Allow at least 30cm (11. 8 inches) between the projector and walls. · Do not insert the projector into any space where air circulation is poor. · Never cover the projector with a blanket or any similar item. Never use the projector while it is on a carpet, blanket, towel, seat cushion, or other pliable surface. Before cleaning the projector, be sure to turn it off and unplug it from the power outlet. Failure to do so creates the risk of electric shock. Location Never locate the projector in any of the following types of locations. · Near an area subject to strong vibration · An area subject to large amounts of moisture or dust · In a kitchen or other area exposed to oil smoke · Near a heater, on a heated carpet, or in an area exposed to direct sunlight · An area subject to temperature extremes (Operating temperature range is 5°C to 35°C (41°F to 95°F)). Heavy objects Never place heavy objects on the projector or climb on top of the projector. Doing so creates the risk of fire and electric shock. ' $ Projector cabinet Water Never locate the projector in a bathroom or anywhere else there is the chance that it will be splashed with water. Cleaning - Unstable location Never place the projector on an unstable surface or on a high shelf. Note that problems caused by unauthorized projector disassembly or modification are not covered by the warranty and are not eligible for repair by CASIO. Laser Precautions This projector is a Class 1 laser device that conforms with IEC 60825-1. Disassembly or modification is very dangerous and should never be attempted. Any operation or adjustment not specifically instructed by the user's guide creates the risk of hazardous laser radiation exposure. Bottom E-6 Operating Precautions Other Precautions This projector is made of precision components. Failure to observe the following precautions can result in inability to correctly save data and malfunction. Never use or store the projector in the following locations. Doing so creates the risk of malfunction of and damage to the projector. Locations subjected to electrostatic charge Locations subjected to temperature extremes Locations where there is extreme moisture Locations subjected to sudden temperature changes Locations where there is a lot of dust On a shaky, slanted, or otherwise unstable surface Locations where there is the danger of getting wet Avoid using the projector under the following conditions. Such conditions create the risk of malfunction of and damage to the projector. Avoid areas subject to temperature extremes (operating temperature range is 5°C to 35°C (41°F to 95°F)). Never place heavy objects on the projector or climb on top of the projector. Never place a vase or any other container of water on top of the projector. Whenever setting the projector down or performing any operation that involves moving or reorienting it, take care that you do not pinch your fingers under the projector. Never leave a dead battery inside the remote controller for a long time. A dead battery can leak, which leads to malfunction of and damage to the remote controller. Clean with a soft, dry cloth. When very dirty, use a soft cloth that has been dampened in a weak solution of water and a mild neutral detergent. Never use thinner, benzine, or any other volatile agent to clean the projector. Doing so can remove its markings and cause staining of the case. Missing Screen Dots Though this projector is manufactured using the most advanced digital technology available today, some of the dots on the screen may be missing. [. . . ] Use the [INPUT] key to select the input source. "Selecting the Input Source" (User's Guide) 9. On the remote controller, use the [ZOOM +] and [ZOOM ­] keys to adjust the projected image size. 10. On the remote controller, use the [FOCUS e] and [FOCUS r] keys to adjust image focus. 11. After you finish projecting, press the [P] (Power) key. This will cause a power down confirmation message to appear. [. . . ]