User manual CASIO AT-5

[. . . ] E USER'S GUIDE Please keep all information for future reference. Safety Precautions Before trying to use the keyboard, be sure to read the separate "Safety Precautions". AT3/AT5-E-1B NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] In response to the "Sure?" message that appears, press the R-14 (YES) button to start extraction or the R-14 (NO) button to cancel. E-79 Using the Song Sequencer Editing a Track The following operations are supported during track (system track, Tracks 01 through 16) editing. · Clearing a single track · Copying one track to another track (Tracks 01 through 16 only) · Combining two tracks into a single track (Tracks 01 through 16 only) To clear a single track 1. Perform the procedure under "To start a track editor operation" on page E-80 to display the track editor menu. 2. Press the R-16 (ENTER) button. · This causes the "Clear Track" screen to appear. To start a track editor operation 1. Press the C-5 (SONG SEQUENCER) button to enter the song sequencer mode. 2. While holding down the R-13 (FUNCTION) button, press the C-5 (EDIT) button to display the edit menu. 3. Use the R-17 (t, y) buttons to move the 0 to "TrackEdit" and then press the R-16 (ENTER) button. · This displays the track editor menu shown below. 3. Use the dial or R-17 (u, i) buttons to specify the track you want to clear. · A black box ( ) above a track number in the level meter indicates that there is already data recorded in that track. · You also can select a track using the dial or R-14 (­, +) buttons. 4. In response to the "Sure?" message that appears, press the R-14 (YES) button to clear or the R-14 (NO) button to cancel. E-80 Using the Song Sequencer To copy one track to another track (Tracks 01 through 16 only) To combine two tracks into a single track (Tracks 01 through 16 only) 1. Perform the procedure under "To start a track editor operation" on page E-80 to display the track editor menu. 1. In the song sequencer mode, use the R-17 (u, i) buttons to select the lower numbered track of those you want to combine. · As an example, we will combine Track 03 and Track 05 into Track 06. Use the R-17 (t, y) buttons to move the 0 to "Copy" and then press the R-16 (ENTER) button. · This causes the "Copy Track" screen to appear. At this time the thick brackets (%) will be located at the "Copy" setting. 2. Perform steps 2 and 3 of the procedure under "To start a track editor operation" on page E-80 to display the track editor menu. 3. Use the dial or R-14 (­, +) buttons to specify the track number you want to copy from. 3. Use the R-17 (y) button to move the 0 to "Merge" and then press the R-16 (ENTER) button. · This displays a "Merge Track" screen like the one shown below. At this time the thick brackets (%) will be located at setting B. 4. Press the R-17 (y) button to move the thick brackets (%) to "To". · An asterisk (*) next to a track number indicates that there is already data recorded in that track. A BC 5. Use the dial or R-14 (­, +) buttons to specify the track number you want to copy to. 6. After everything is the way you want, press the R-16 (ENTER) button. · If the copy destination track does not contain recorded data, the copy operation is performed immediately. · If the copy destination track already contains recorded data, the confirmation message shown below appears asking if you want to overwrite the existing data. A: One of the tracks to be combined (The track you selected in step 1 is the initial default selection). B: Other track to be combined. [. . . ] 4 :Noise2 Level (0, 1, 2, 3, 4, 5) Adjusts the level of Noise Generator 2. 5 :Noise2 Density (0, 1, 2, 3, 4, 5) Adjusts the frequency of Noise Generator 2. Raising the noise level while a note is not sounding will cause noise to sound, even if there is no input signal. Dual Type DSP Parameters Dual type DSPs are configured by combining two different single type DSPs. Use the procedure below to determine what parameters that can be configured for each dual type DSP, and the operation, and setting ranges of dual type DSPs. [. . . ]