User manual CASIO 4732

[. . . ] MO0605-EA Operation Guide 4732 4733 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully. About This Manual (Light) · The measurement functions built into this watch are not intended for use in taking measurements that require professional or industrial precision. Values produced by this watch should be considered as reasonably accurate representations only. · When fishing, always take proper precautions to ensure your own personal safety and the personal safety of others around you. [. . . ] · If a measurement error occurs for some reason, only a single the dot in the center column will be displayed. Temperature change greater than +10. 0°C (+18. 0°F) Temperature change greater than ­10. 0°C (­18. 0°F) Error To configure countdo star t time and auto-repeat settings wn 1. While the countdown start time is on the display in the Auto-repeat on indicator Countdown Timer Mode, hold down A until the hour setting of the countdown start time starts to flash, which indicates the setting screen. · If the countdown start time is not displayed, use the procedure under "To use the countdown timer" to ll l display it. Press C to move the flashing in the sequence shown below, and select the setting you want to change. llll lll llll On/Off status Start Time (Hours) Start Time (Minutes) Auto-Repeat On/Off Recalling Temperature Data The measurements the watch takes at the top and the bottom of each hour are stored in memory automatically. You can use the Temperature Data Recall Mode to recall memory data when you need it. The newest data record is number 01, while the oldest data record is the one with the highest number. · When there are already 50 records in memory, storage of a new temperature reading causes the oldest record (record number 50) to be deleted automatically to make room for the new data. The new data is assigned record number 1, and all of the numbers of all the other records (01 to 49) are incremented by 1 (becoming 02 through 50). 3. Perform the following operations, depending on which setting is currently selected on the display. · While the start time setting is flashing, use D (+) and B (­) to change it. · While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press D to toggle auto-repeat on (0N) and off (0F). · The auto-repeat on indicator ( ) is displayed on the Countdown Timer Mode screen while this function is turned on. · Frequent use of auto-repeat and the alarm can run down battery power. Alarm Alarm time While the alarm is turned on, the watch beeps when the (Hour : Minutes) alarm time is reached. You can also turn on an Hourly AM indicator To recall temperature recor ds 1. In the Timekeeping Mode, press C twice to enter the Temperature Data Recall Mode. Temperature · This displays the newest record currently in memory. · Pressing D while the oldest record is displayed will scroll to the newest record. · If a temperature measurement operation is performed while a record is displayed, the displayed record's number will be incremented by 1. · If an error occurs during temperature measurement, ``--. -'' will be shown for the temperature value in the corresponding record. Data storage time Record number Time Signal, which will cause the watch to beep twice every hour on the hour. · All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C. Alarm on indicator Hourly time signal on indicator To set the alarm time 1. In the Alarm Mode, hold down A until the hour setting of the alarm time starts to flash, which indicates the setting screen. · When setting the alarm time using the 12-hour format, take care to set the time correctly as a. m. [. . . ] Once you set the date, there should be no reason to change it except after you have the watch's batteries replaced. Timekeeping Moon Module Phase 4732 Indicator Module 4733 Moon Age Moon Phase 0. 0 - 1. 8 1. 9 - 5. 5 5. 6 - 9. 2 9. 3 - 12. 9 13. 0 - 16. 6 16. 7 - 20. 2 27. 7 - 29. 5 First Full New Quarter Moon Moon (Waxing) 20. 3 - 23. 9 24. 0 - 27. 6 Last Quarter (Waning) · The Moon phase indicator shows the Moon as viewed at noon from a position in the Northern Hemisphere looking south. Note that at times the image shown by the Moon phase indicator may differ from that of the actual Moon in your area. · The left-right orientation of the Moon phase is reversed when viewing from the Southern Hemisphere or from a point near the equator. World Time · The seconds count of the World Time is synchronized with the seconds count of the Timekeeping Mode. · All World Time Mode times are calculated from the current time in the Timekeeping Mode using UTC time differential values. lll llll lll llll To turn on illumination manually In any mode (except when a setting screen is on the display), press B to illuminate the display for about one second. [. . . ]