User manual CASIO 4335

[. . . ] MO0607-EB Operation Guide 4335 4348 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully. · The measurement functions built into this watch are not intended for use in taking measurements that require professional or industrial precision. Values produced by this watch should be considered as reasonably accurate representations only. [. . . ] · The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. · All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. The alarm sounds at the preset time for 10 seconds, regardless of the mode the watch is in. · To stop the alarm tone after it starts to sound, press any button. To test the alarm In the Alarm Mode, hold down D to sound the alarm. To turn the Daily alarm and the Hourly Time Signal on and off In the Alarm Mode, press D to cycle through the settings shown below. Module 4335 Seconds Hours Alarm Off Signal Off Alarm On Signal Off Alarm Off Signal On Alarm On Signal On To measure times with the stopwatch Elapsed Time D Start D Stop D Re-start D Stop A Clear Module 4348 Split Time D Start A Split (SPL displayed) A Split release D Stop A Clear · The alarm on indicator and the Hourly Time Signal on indicator are shown on the display in all modes while these functions are turned on. Two Finishes D Start A Split First runner finishes. Display time of first runner. World Time D Stop Second runner finishes. A Split release Display time of second runner. A Clear Day of the week and day in the selected city Countdown Timer You can set the countdown timer within a range of one minute to 100 hours. · You can also select auto-repeat, which automatically restarts the countdown from the original value you set whenever zero is reached. · All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C. City code Current time in selected city Hours Minutes Second To use the countdown timer Press D while in the Countdown Timer Mode to start the countdown timer. · When the end of the countdown is reached and auto-repeat is turned off, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is automatically reset to its starting value after the alarm stops. · When auto-repeat is turned on, the countdown will restart automatically without pausing when it reaches zero. · The countdown timer measurement operation continues even if you exit the Countdown Timer Mode. · To stop a countdown operation completely, first pause it (by pressing D), and then press A. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the hour Auto-repeat on indicator setting of the countdown start time starts to flash, which indicates the setting screen. · If the countdown start time is not displayed, use the procedure under "To use the countdown timer" to ll l display it. Press C to move the flashing in the sequence shown below, and select the setting you want to change. llll To view the time in another city While in the World Time Mode, press D to scroll eastward through the city codes (time zones) or B to scroll westward. To toggle a city code time between Standard Time and Daylight Saving Time 1. In the World Time Mode, use D and B to display the city code (time zone) whose Standard Time/Daylight Saving Time setting you want to change. Hold down A to toggle between Daylight Saving Time (DST indicator displayed) and Standard Time (DST indicator not displayed). · The DST indicator is shown on the World Time screen while Daylight Saving Time is turned on. DST indicator · Note that changing the Daylight Saving Time for any city code causes the setting to be applied to all city codes. Illumination Auto light switch on indicator 3. Perform the following operations, depending on which setting is currently selected on the display. · While the start time setting is flashing, use D (+) and B (­) to change it. · While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press D to toggle auto-repeat on (0N) and off (0F). [. . . ] The lunitidal interval differs according to your current location, so you must specify a lunitidal interval in order to obtain the correct tide graph readings. The tide graph displayed by this watch is based on the current Moon age. Remember that the margin for error of the Moon age displayed by this watch is ± 1 day. The greater the error in a particular Moon age, the greater the error in the resulting tide graph. · The seconds count of the World Time is synchronized with the seconds count of the Timekeeping Mode. [. . . ]