User manual CASIO 3768

[. . . ] MA0508-EC Operation Guide 3768/3769 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully and keep it on hand for later reference when necessary. Important! The fishing/hunting level indicator and moon phase indicator produced by this watch are all based on calculations that use the watch's current time, date, and Home Site settings. Because of this, you should make sure that the current date and time, and your Home Site data are all correct before using the indicators. · When fishing or hunting, always take proper precautions to ensure your own personal safety and the personal safety of others around you. [. . . ] Hold down A until the current digital time starts to flash, which indicates the analog setting screen. · Holding down D advances the analog time setting at high speed. · If you need to advance the analog time setting a long way, hold down D until the time starts advancing at high speed, and then press B. This locks the highspeed hand movement, so you can release the two buttons. It will also stop automatically after the time advances 12 hours or if an alarm (multi-function alarm, Hourly Time Signal, or countdown beeper) starts to sound. · The watch will automatically adjust the minute hand slightly to match its internal second count when you exit the setting screen. · To return to the Timekeeping Mode, press C. 1/100 second The stopwatch lets you measure elapsed time, split times, and two finishes. · The display range of the stopwatch is 23 hours, 59 minutes, 59. 99 seconds. · The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. · The stopwatch measurement operation continues even if you exit the Stopwatch Mode. · Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement. · All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. To measure times with the stopwatch Elapsed Time Start Split Time Start Two Finishes Start Split First runner finishes. Display time of first runner. Stop Re-start Stop Clear Fishing/Hunting Mode Moon phase indicator Time Split (SPL displayed) Split release Stop Clear Year Month ­ Day Fishing/hunting level indicator Fishing/Hunting Level Screen The Fishing/Hunting Mode displays an indicator that shows, as one of five levels, the suitability of a specific date and time (minute 00 to minute 59 of a particular hour) for fishing or hunting. This mode also can be used to display Moon Data (Moon age and Moon phase) for a specific date. · If you doubt that the fishing/hunting level indicator or current Moon data is wrong for some reason, check the current Timekeeping Mode settings (time, date, and Home Site), and correct them if required. · See "Moon Phase Indicator" for information about the Moon phase indicator. · All of the operations in this section are performed in the Fishing/Hunting Mode, which you enter by pressing C. Stop Second runner finishes. Split release Display time of second runner. Clear Countdown Timer Hours Minutes Seconds Fishing/Hunting Level Indicator The fishing/hunting level indicator shows the relative favorability of a fishing/hunting time (calculated in accordance with Moon transit and phase) as shown in the table below. Level 5 Level 4 Level 3 Level 2 Level 1 * These indicators actually appear during Moon ages 13. 0 to 16. 6 (Full Moon and phase immediately preceding it) and 27. 7 to 1. 8 (New Moon and phase immediately preceding it). You can set the countdown timer within a range of one minute to 24 hours. In the Alarm Mode, use D to select a one-time alarm (alarm number 2 or 3) or the Hourly Time Signal (:00). · Turning on a one-time alarm (2 or 3) displays the alarm on indicator on its screen. · Turning on the Hourly Time Signal displays the hourly time signal on indicator. Alarm on indicator · The alarm on (ALM) indicator and Hourly time Signal on (SIG) indicator are displayed in all modes. 3. While a setting is flashing, use D and B to change it as described below. Screen To do this: Change the hours or minutes Toggle auto-repeat on (ON) and off (OF) Do this: Use D (+) and B (­). [. . . ] In the case of the snooze alarm, the alarm operation is performed a total of seven times, every five minutes, until you turn the alarm off or change it to a onetime alarm. · To stop the alarm tone after it starts to sound, press any button. · Performing any one of the following operations during a 5-minute interval between snooze alarms cancels the current snooze alarm operation. Displaying the Timekeeping Mode setting screen Displaying the alarm1 setting screen To test the alarm In the Alarm Mode, hold down D to sound the alarm. 3 Operation Guide 3768/3769 Reference This section contains more detailed and technical information about watch operation. [. . . ]