User manual CASIO 3206

[. . . ] MO0909-EA Operation Guide 3135 3206 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully. · The watch continues to operate, even when it is not exposed to light. Leaving the watch in the dark can cause the battery to run down, which will result in some watch functions being disabled. [. . . ] The calculation operation takes about 10 seconds, and is indicated by movement in the Moon Phase indicator and the Tide Graph on the display. You can use A and C to change to another date while a calculation operation is in progress. · After calculation is complete, the Moon information (Moon age and phase) and tide information (current tide level and tide range) will be displayed for the date you selected. Measurement date (Month ­ Day) Measurement time (Hour : Minute) 2. While the Moon information (Moon age and phase) and tide information (tide level and tide range for the current date) are displayed, you can press B (+) to advance the displayed tide range by one hour. · Update of the Moon Phase indicator and the Tide Graph is stopped while any of the following is occurring. During button operation While an alarm is sounding While a countdown beeper is sounding During display illumination During a 2-hour barometric pressure reading operation 1. In the Data Recall Mode, hold down E until CLR flashes on the display and the watch beeps twice. · Releasing E at any time while CLR is flashing on the display will cancel the delete operation. · The watch will beep to indicate that all of the altitude data stored in watch memory (including readings you stored and the high altitude value) is deleted. L Adjusting the High Tide Time Use the following procedure to adjust the high tide time within a particular date. You can find out high tide information for your area from a tide table, the Internet, or your local newspaper. To adjust the high tide time 1. In the Tide/Moon Data Mode, use A (+) and C (­) to select the date you want. · After you select a date, the watch starts to calculate Moon and tide data for the date you selected. The calculation operation takes about 10 seconds, and is indicated by movement in the Moon Phase indicator and the Tide Graph on the display. You can use A and C to change to another date while a calculation operation is in progress. · After calculation is complete, the Moon information (Moon age and phase) and tide information (current tide level and tide range) will be displayed for the date you selected. ll lll l lll 6 Operation Guide 3135 3206 Hour l lllll l lll l l ll l ll lll ll l l lll Minute lllll lllll l l ll l ll l l ll l lll ll l l lll ll l 2. While the Moon information (Moon age and phase) and tide information (current tide level and tide range) are displayed, hold down E until the hour digits start to flash. When the minute setting is the way you want, press E to exit the adjustment screen and return to the Tide/Moon Data Mode screen. · Pressing A and C at the same time while the time adjustment screen is displayed (steps 2 through 5 above) will return the high tide time to its initial factory default setting. Countdown End Beeper The watch beeps each second of the final 10 seconds before a countdown reaches zero, and at zero. The first five beeps (seconds 10 through 6) are higher pitched than the final five beeps (seconds 5 through 1). The watch emits a longer beep to signal when the countdown reaches zero. l lllll l ll lll llll · The high tide time setting is not affected by the DST (summer time) setting of the Timekeeping Mode. The second high tide time for that day is adjusted automatically based on the first high tide time. Reversing the Displayed Moon Phase The left-right (east-west) appearance of the Moon depends on whether the Moon is north of you (northerly view) or south of you (southerly view) as you view it. You can use the procedure below to reverse the displayed Moon phase so it matches the actual appearance of the Moon where you are located. [. . . ] It takes approximately 20 to 30 minutes for the case of the watch to reach the actual surrounding temperature. Pressure Sensor and Temperature Sensor Calibration The pressure sensor and temperature sensor built into the watch are calibrated at the factory and normally require no further adjustment. If you notice serious errors in the pressure readings and temperature readings produced by the watch, you can calibrate the sensor to correct the errors. · Incorrectly calibrating the barometric pressure sensor can result in incorrect readings. Before performing the calibration procedure, compare the readings produced by the watch with those of another reliable and accurate barometer. [. . . ]