User manual CASIO 3199

[. . . ] Toggle between Daylight Saving Time ( ) and Standard Time ( Change the city code. Press D. Day of week Hour : Minutes PM indicator Month ­ Day Change the month or day. Toggle the setting between 1. 5 seconds ( ) and 3 seconds ( ). Switching Between Time Screens Each press of D cycles the time screens in the sequence shown below. · See "Daylight Saving Time (DST)" for details about DST setting. · The day of the week is displayed automatically in accordance with the date (year, month, and day) settings. Daylight Saving Time (DST) Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time. [. . . ] · To stop the alarm tone after it starts to sound, press any button. To turn on illumination In any mode (except when a setting screen is on the display), press B to turn on illumination. · You can use the procedure above to select either 1. 5 seconds or 3 seconds as the illumination duration. When you press B, the illumination will remain on for about 1. 5 seconds or 3 seconds, depending on the current illumination duration setting. To test the alarm In the Alarm Mode, hold down D to sound the alarm. Press A to cycle through the alarm settings as shown below. World Time City code World Time shows the current time in 48 cities (31 time zones) around the world. · All of the operations in this section are performed in the World Time Mode, which you enter by pressing C. Current time and date in the zone of the selected city code To view the time for another city code In the World Time Mode, press D to scroll eastwardly through city codes. · For full information about city codes, see the "City Code Table". · If the current time for a city is wrong, check your Timekeeping Mode time and time zone settings and make the necessary changes. Alarm Off One-Time Alarm On Daily Alarm On · In all modes, the alarm on indicator is shown for the alarm that is currently turned on. · The alarm on indicator flashes while the alarm is sounding. To toggle a city code time between Standard Time and Daylight Saving Time 1. In the World Time Mode, use D (east) to display the city code (time zone) whose Standard Time/Daylight DST indicator Saving Time setting you want to change. Hold down A for about one second to toggle Daylight Saving Time (DST displayed) and Standard Time (DST not displayed). · The DST indicator is on the display whenever you display a city code for which Daylight Saving Time is turned on. · Note that the DST/Standard Time setting affects only the currently displayed city code. · Note that you cannot switch between Standard Time and Daylight Saving Time while UTC is selected as the city code. In the World Time Mode, use D to display the city you want to make your new Home Time city. · This makes the World Time city you selected in step 1 your new Home Time city. To turn the Hourly Time Signal on and off 1. In the Alarm Mode, use D to select the Hourly Time Hourly time signal Signal. · The Hourly Time Signal on indicator is shown on the display in all modes while this function is turned on. Countdown Timer Seconds The countdown timer can be set within a range of one second to 24 hours. · All of the operations in this section are performed in the Countdown Timer Mode, which you enter by pressing C. Alarms Alarm on indicator Hours Minutes 1/10 second Alarm number Alarm time (Hour : Minutes) Your watch has a total of five alarms, each of which you can configure as a daily alarm or one-time alarm. · One-time Alarm: Sounds once at the preset time and then is disabled automatically. You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour. · All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C. · Alarms operate in coordination with the current Home City Time. To configure the countdown timer 1. [. . . ] · Holding down C to turn the button operation tone on or off also causes the watch's current mode to change. · The mute indicator is displayed in all modes when the button operation tone is turned off. +9 +9. 5 +10 +11 +12 +1 Auto Return Features · If you leave the watch in the Alarm Mode for two or three minutes without performing any operation, it automatically changes to the Timekeeping Mode. · If you leave a screen with flashing digits on the display for two or three minutes without performing any operation, the watch automatically exits the setting screen. +2 · Based on data as of December 2008. · The rules governing global times (UTC offset and GMT differential) and summer time are determined by each individual country. Scrolling The B and D buttons are used in various modes and setting screens to scroll through data on the display. [. . . ]