User manual CARVIN AG100D2003

[. . . ] 12" PS12 or 15" PS15 woofer (depending on model purchased) High frequency tweeter with adjustable L-Pad on crossover. 12" Cabinet Response: 63Hz to 16. 5kHz Congratulations on your purchase of the AG100D Series III amplifier. We've included all of the great features a solo performer needs, such as three independent channels with separate volume and EQ, MID sweep control, phantom mic power and 5 band Graphic EQ. Additional features include, mid & HI Contour switches on channel 1, Bass and Mid Contour switches on channel 2. [. . . ] Then, as needed, turn the turn to the right to boost, or to the left to cut to change the sound. XLR MICROPHONE & 1/4" INPUT JACKS The MIC input is designed for balanced low impedance ( microphone ) input signals. The Balanced input will reduce the common noise picked up on the microphone cables. The XLR connector is wired as per the industry standard; pin 1 is ground, pin 2 is positive and pin 3 is negative. This allows condenser microphones to be run directly without the need for batteries or other external phantom power supplies. The 1/4" jack is designed for unbalanced high impedance signals (guitar, tape deck, drum machine, etc. ). VOLUME CONTROL The VOLUME control adjusts the volume of the channel heard in the speaker, the line out jack, and the headphone jack. LO AND HI TONE CONTROLS The LO and HI tone controls are used to shape the bass and treble sound of the input signal. It is suggested that the tone control settings start in their center positions where they do not effect the signal. Then, as needed, turn the turn to the right to boost, or turn to the left to cut to change the sound. DIGITAL SIGNAL PROCESSING The 24 bit processor will provide a host of awesome sounding effects that include: Flange, Reverb, Echo, & Chorus. The master EFFECT 1 & 2 control will adjust the volume level of the selected effect. Remember each channel has its own EFFECT send level that will adjust the amount of signal sent to the effects processor. (Note: When adjusting the effects on either channel, an audible noise may be heard). EFFECT PARAMETERS Each of the four effects has a variable parameter that can be easily adjusted. ECHO: When the top SELECT control is at the "7 O-clock" position, it is selected to the first ECHO setting where you get a single repeat echo (minimal regeneration). Turning the PARAMETER control to 1 will provide the shortest delay time between the original signal and the echo. Increasing the PARAMETER control to the right will increase the time delay between the original signal and the echo. To increase the number of echoes, turn the SELECT control clockwise to "9 O-clock" (maximum regeneration). REVERB: When the SELECT control is at the "10 O-clock" position, it is selected 3 12 3 6 9 12 3 3 3 6 9 6 9 12 3 6 9 3 6 9 12 3 6 9 12 6 9 3 3 6 9 EFF2 3 3 6 9 3 6 9 12 3 6 9 12 6 9 3 3 6 9 EFF2 RE RE LO 0 12 12 LO EFF1 12 EFF1 PARAMETER MID HI MID INPUT 1 VOLUME 456 3 7 2 8 1 9 0 10 EFF OFF INPUT 2 3 6 9 3 6 9 EFF1 EFF2 VOLUME 456 3 7 2 8 1 9 0 10 MIC TAPE/CD VOLUME 456 3 7 2 8 1 9 0 10 456 3 7 2 8 1 9 0 10 PK 3 2 1 456 0 7 8 9 10 PK CH 1 CH 2 CH 3 3 2 1 456 LEVEL 3 2 1 0 7 8 9 10 456 0 7 8 9 10 1 2 3 6 7 9 10 E E FREQ GAIN 0 1K MID 3 3 800 2K 6 6 6 9 9 9 300 3K 12 12 12 HIGH 0 3 LO 0 HI 0 EFF OFF LO 0 HI 0 EFF OFF V HO EFF1 ER EFF2 O R B CH V ER B CH O R ACOUSTIC GUITAR AMP DUAL 24-BIT EFFECTS AG100D US US 6 9 12 6 9 12 HO FLA N FLA N EC EC G G + 12 8 4 0 4 8 12 GRAPHIC EQ POWER 3 2 1 - 7 8 9 0 10 MASTER 456 100 250 800 6K 12K 13 14 15 EFF1 RE RE EFF2 O R V ER B CH V ER B CH O R PARAMETER CHORUS: When the SELECT control is at the "1 O-clock" position it is selected to the first CHORUS setting. Turning the SELECT control clockwise will increase the 1 amount reverb in the chorus. Turning the PARAMETER control to 1 will provide a minimal chorus depth setting. [. . . ] Refer to replacement text on the unit for correct fuse type. HELP SECTION 1) AMP WILL NOT TURN ON Check the power to the amp. Check for tripped circuit breakers, unplugged extension cords or power-strip switches that may be turned off. After you have verified there is AC power and the amp still doesn't work, your unit will require servicing. 2) MAINTENANCE To bring back the new look, your AG100D cabinet can be wiped with mild detergent and/or a warm damp soft cloth. [. . . ]