User manual CANTON DIGITAL MOVIE

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CANTON DIGITAL MOVIE. We hope that this CANTON DIGITAL MOVIE user guide will be useful to you.


CANTON DIGITAL MOVIE : Download the complete user guide (1749 Ko)

Manual abstract: user guide CANTON DIGITAL MOVIE

Detailed instructions for use are in the User's Guide.

[. . . ] Die Adressen der internationalen Canton-Vertriebspartner finden Sie unter: The addresses of Canton's international distributors can be found at: Please read these operating instructions carefully and keep them for reference. Canton cannot be held liable for any damage resulting from non-compliance with the following instructions. Choose a level, dry and clean place for your speakers, away from windows with direct sunlight, heat sources, vibrations, high humidity and extreme cold. Contact your authorized dealer or a qualified repair specialist in the event of problems or defects. [. . . ] If you want to switch the DM system off, press again to put the DM system into standby mode. Please note that the DM system inputs are switched over with < input > while <select> regulates the devices to be controlled remotely. You can select the following sources with tv, vcr, aux, tuner, dvd, sat : Note: To do justice to the various recording philosophies, especially with music recordings, we have implemented two surround modes. Use , , surround 2" above all when the speech is difficult to understand (e. When the voice reproduction seems to be unusually muffled and unintelligible). Use to select whether the sound is to be reproduced in the stereo or surround mode. the system sets the corresponding decode mode automatically , depending on the input signal. Stereo or PCM are activated as analog sound in the , , stereo" play mode, Virtual Dolby Digital, Virtual Dolby Pro Logic II or Virtual DTS in the , , surround 1 und surround 2 / 2. Once you have successfully connected your DM system, you should then adapt the individual components to your listening area. If you want to adjust the settings of your DM system, please switch it on and select Speaker Setup or Parameter Setup by pressing the MENU key once or twice respectively. This will not work if the tuner has been selected as the source device. Begin by measuring the distance between the individual components of the DM system and your preferred listening position (in line with the Distance Setup graphs for DM1 and DM2). enter these values in the menu at the corresponding speaker (Subwoofer , Front Left , Front Right) under `Distance'. The volume of the satellites and central surround should be the same at the listening position. 1 mode additionally includes the center, rear right and rear left speakers. You can determine under Output whether the lower pre-amplifier output on the back of the subwoofer is switched as Line Out (fixed volume level for an analog recording device) or as Zone 2 (adjustable volume for an active multi-room system or wireless loudspeaker system, for example). It is used to adjust the treble and bass tones of the satellites to the listening area. Here are a few tips on this: In severely acoustically dampened rooms ­ turn up the treble In resonant rooms ­ turn down treble In a freestanding position ­ turn up bass When satellites are positioned close to a wall ­ turn down bass Irrespective of all of this: let your own ear decide. When playing movies, we recommend the , , expand normal" or , , expand medium" settings. The picture can be synchronized with the sound using lip sync in order to coordinate speech with delayed lip movements, for example. 1 multi-channel recordings (DolbyDigital or DTS) through ZONE 2/LINE OUT, , , dynamic" must be set at , , compressed". The Canton DM systems have an integrated FM tuner which is selected via the input keys in the main menu of the remote control. [. . . ] The polarity between the sub and satellites or among the satellites is wrong 2. The sound gets obliterated in the transfer area because of the different positions of the sub and satellites Raise the treble level as described in , , room comp function treble" (p. Raise the treble level as described in , , room comp function treble" (p. Raise the bass level in the transfer area as described in , , room comp function bass" (p. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CANTON DIGITAL MOVIE




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CANTON DIGITAL MOVIE will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.