User manual CANON POWERSHOT SX160 IS BROCHURE

[. . . ] It may damage the camera, or the camera may not recognize the card, if it is inserted incorrectly. See the Advanced Guide: Handling the Memory Card (p. 25). 5 To Remove the Memory Card Push the memory card with your finger until the memory card clicks and then release it. You can use SD memory cards, SDHC memory cards and MultiMediaCards with this camera. These cards are collectively called memory cards in this guide. 6 First Time Settings Setting the Date/Time a b c 1. Use the or button to select an item and the or button to change its value (b). [. . . ] The zoom can be adjusted from 35 mm ­ 140 mm (focal length) in 35mm film equivalent terms. Telephoto: Zooms in on the subject. Press the button to switch between modes. :Auto :On :Off See the Advanced Guide: Setting the Red-Eye Reduction Function (p. 28). cannot be set in mode. See the Advanced Guide: Functions Available in Each Shooting Mode (p. 9). You are recommended to shoot with the camera attached to a tripod or other device if the camera shake warning icon appears. 12 When the LCD monitor is on and flash recharging begins, the indicator blinks orange and the LCD monitor turns off. When recharging ends, the indicator turns off and the LCD monitor turns on. The time required for flash recharging will change depending on usage conditions and remaining battery power. Shooting Close-ups (Macro) 1. Press the button. Shooting To cancel the macro mode, press the or display. button to turn off the Use this mode to shoot close-ups of flowers or small items. Macro Image Area at Minimum Focusing Distance from End of Lens to Subject · Maximum wide angle setting: 60 x 45 mm (2. 4 x 1. 8 in. ) Minimum focusing distance: 5 cm (2. 0 in. ) · Use the LCD monitor to compose close-ups in macro mode since images composed with the viewfinder may be off-center. · Check the range of the built-in flash when using it in macro mode (Advanced Guide p. This setting cannot be set in some shooting modes. See the Advanced Guide: Functions Available in Each Shooting Mode (p. 18). * Default setting. · When the shutter button is pressed fully, the self-timer lamp will blink. 25) Connecting the Camera to a Computer · Basic Guide (pp. 24, 25) Downloading Images to a Computer · Basic Guide (pp. 26, 28, 29) · Software Starter Guide · Software Starter Guide Using a Memory Card Reader A memory card reader can be used with all the operating systems listed above. See the Software Starter Guide for details. 22 System Requirements Please install the software on a computer meeting the following minimum requirements. Windows OS Windows 2000 Service Pack 4 Windows XP (including Service Pack 1 and Service Pack 2) Windows Vista The above OS should be pre-installed on computers with built-in USB ports. Windows 2000/Windows XP: Pentium 500 MHz or higher Windows Vista: Pentium 1. 3 GHz or higher Windows 2000/Windows XP: Windows Vista: USB · Canon Utilities - ZoomBrowser EX - PhotoStitch · Canon Camera TWAIN Driver 200 MB or more 40 MB or more 25 MB or more 256 MB or more 512 MB or more Downloading Images to a Computer Computer Model CPU RAM Interface Free Hard Disk Space Display 1, 024 x 768 pixels/High Color (16 bit) or better Macintosh OS Computer Model CPU RAM Interface Free Hard Disk Space Display Mac OS X (v10. 3 ­ v10. 4) The above OS should be pre-installed on computers with built-in USB ports. PowerPC G3/G4/G5 or Intel processor 256 MB or more USB · Canon Utilities - ImageBrowser - PhotoStitch 200 MB or more 40 MB or more 1, 024 x 768 pixels/32, 000 Colors or better 23 Preparing to Download Images Ensure that you install the software first before connecting the camera to the computer. Items to Prepare · Camera and computer · Canon Digital Camera Solution Disk supplied with the camera · Interface cable supplied with the camera 1. Place the Canon Digital Camera Solution Disk in the computer's CD-ROM drive. When the installation is complete, click either the [Finish] or [Restart] button that appears. Remove the Canon Digital Camera Solution Disk from the CD-ROM drive when your normal desktop screen appears. Double-click the [Canon Digital Camera Installer] in the CDROM window. Use the supplied interface cable to connect the computer's USB port to the camera's DIGITAL terminal. Slip your fingernail under the right edge of the camera's terminal cover, lift it open and plug the interface cable in all the way. USB Port DIGITAL Terminal Interface Cable Interface Cable Downloading Images to a Computer 2. [. . . ] · To cancel the download, press the FUNC. /SET button. 29 Select & Transfer/Wallpaper 2. · Images can also be selected during index playback (Advanced Guide p. · Press the MENU button to return to the Direct Transfer menu. button (or the button 3. Select images to download and press the Only JPEG images can be downloaded as wallpaper for a computer. [. . . ]