User manual CANON PIXMA MP970

[. . . ] (2) Move the Scanner Lock Switch towards the release mark to unlock the Scanning Unit (Printer Cover). (2) a Pull the orange tape in the direction of the arrow to peel off the protective film and remove the film completely. Extension Paper Guide (1) Press the { or } button to select the language. (1) (2) Press the OK button. Caution There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. b Remove the orange protective cap from the Print Head and discard it. Electrical Contacts If the air hole is blocked with the remaining film, ink may leak out or may not eject properly. b Twist off and discard the orange protective cap located on the bottom of the ink tank. Protective Cap Ink Port Do not press! Scanning Unit (Printer Cover) Important If an unintended language is displayed on the LCD, press the Back button on the Operation Panel to return to the Language selection screen. Caution · Make sure to unlock the Scanning Unit (Printer Cover) before turning on the machine. · Before transporting the machine, always lock the Scanning Unit (Printer Cover) by moving the Scanner Lock Switch towards the lock mark. Once the message "Install the print head and set the ink tank. " appears, go to e. b Load a sheet of A4 or Letter-sized plain paper e Lift the Scanning Unit (Printer Cover) until it locks into place. [. . . ] And Print Head is aligned automatically. OK Important If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center. Serial Number Location Note · The pattern is printed in black and blue. · When Automatic Print Head Alignment cannot be executed correctly, the message "Auto head align has failed. " is displayed on the LCD. Refer to "An Error Message is Displayed on the LCD" in the Quick Start Guide. Hardware setup and Print Head alignment are complete. USB connection is explained here. For wired LAN connection, refer to the Network Setup Guide. Windows® Software Installation w s g When the list of applications to install appears, confirm the contents and click Install. Note Move the cursor over items to display explanations of each application. Macintosh® Software Installation to sh h When the Setup Complete screen appears, click Next. do W in h Read the License Agreement carefully and click Yes. The Note · The screens below refer to Windows VistaTM operating system Ultimate Edition (hereafter referred to as "Windows Vista") installation. · Before installing the software, disable all anti-virus programs and automatically loading programs. · A message asking for your confirmation to restart your computer may appear during the installation process. If this message is displayed, follow the on-screen instructions and click OK. The installation resumes from where it left off when your computer has been restarted. · If the computer is restarted during installation, do not remove the Setup CD-ROM during restarting. software installation screen may appear during the installation process. printer via USB, then click Next. i When the Setup Method screen appears, select Use the M Note · Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v. 10. 2. 7 or earlier are not supported, do not connect the machine to these. · Before installing the software, disable all anti-virus programs and automatically loading programs. ac in i When the User Registration screen appears, click Next. Note To register later, click Cancel and go to Step j. After software installation is complete, double-click on the desktop. a Connect one end of the USB cable to the computer and the other to the machine. Note Make sure the machine is turned on. a Be sure to TURN THE MACHINE OFF before continuing. (1) Press the ON/OFF button. (2) Make sure that the Power lamp stops flashing. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine. See Step 1- f on the front page. b Turn the computer on and start Windows. Important If the Found New Hardware or Found New Hardware Wizard screen appears automatically, remove the USB cable connected to your computer. In Windows Vista, the screen may close automatically when the USB cable is unplugged. Then turn off the machine and proceed from step c to install the software. j When the Printer Connection screen appears, connect one end of the USB cable to the computer, the other to the machine, then TURN THE MACHINE ON. The software will begin identifying the printer port being used. Important If you cannot go to the next procedure after three minutes, refer to "Cannot Install the MP Drivers" in the Quick Start Guide. j When the Installation completed successfully screen appears, click Restart. Remove the CD-ROM after clicking Restart and restarting the computer. USB b Turn on your Mac and insert the Setup CD-ROM. Note If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop. USB To Computer c Double-click the Setup icon. [. . . ] See Step 1- f on the front page. f When the list of applications to install appears, confirm the contents, then click Install. Note Move the cursor over items to display explanations of each application. Software installation is now complete. m When the PIXMA Extended Survey Program screen f When the main menu appears, click Easy Install. The MP Drivers, On-screen Manuals, and application software are installed automatically. appears, confirm the message. We would appreciate it if you would take part in this program regarding the use of Canon printers. appears, click Exit. g Read the License Agreement carefully and click Yes. The n When the Installation completed successfully screen After clicking Exit, remove the CD-ROM. [. . . ]