User manual CANON LASERBASE MF5730

[. . . ] After you finish reading this guide, store it in a safe place for future reference. Manuals for the Machine The manuals for this machine are divided as follows. Depending on the system configuration and product purchased, some manuals may not be needed. Guides with this symbol are PDF manuals included on the accompanying CD-ROM. CD-ROM · Setting Up the Machine · Software Installation · Network Setting (Only for the MF 5770 model. ) · Introduction on Use Set-Up Sheet Quick Reference Guide User's Guide (This Manual) Facsimile Guide Only for the MF5750/MF5770 models. · Copying and Printing Instructions · Troubleshooting · Fax Instructions · Troubleshooting · Software Installation and Instructions · Printing, Scanning and PC Faxing Instructions · Troubleshooting · Remote User Interface Instructions CD-ROM Software Guide CD-ROM Remote UI Guide Only for the MF5770 model. CD-ROM · Network Connectivity and Setup Instructions Network Guide Only for the MF5770 model. CD-ROM · To view the manual in PDF format, Adobe Reader/Acrobat Reader/Acrobat is required. If Adobe Reader/Acrobat Reader/Acrobat is not installed on your system, please download it from the Adobe Systems Incorporated website. This equipment conforms to the essential requirements of EC Directive 1999/5/EC. [. . . ] Once the job is deleted, the job cannot be restored. 6 Press [Stop/Reset] to return to the standby display. Confirming and Deleting a Print Job 1 2 Press [Status Monitor]. Press [ (-)] or [ (+)] to select <PRINT STATUS> press [OK]. NOTE · If there is no job, <NO PRINT JOBS EXIST> is displayed. · If there is only one print job, go to step 4. 3 4 5 Press [ (-)] or [ (+)] to confirm the file name. If you want to delete the print job, press [OK]. If you decide to delete the job, press [ (-)] for <YES>. 7 Status Monitor NOTE · To cancel deleting the job, press [ (+)] for <NO>. Using characters other than those in ASCII cord may have the LCD display garbled characters. 6 Press [Stop/Reset] to return to the standby display. Confirming and Deleting a Report Job 1 2 Press [Status Monitor]. Press [ (-)] or [ (+)] to select <REPORT STATUS> press [OK]. NOTE · If there is no job, <NO REPORT JOBS EXIST> is displayed. · If there is only one report job, go to step 4. 3 4 5 Press [ (-)] or [ (+)] to confirm the report. If you want to delete the report job, press [OK]. If you decide to delete the job, press [ (-)] for <YES>. NOTE To cancel deleting the job, press [ (+)] for <NO>. Once the job is deleted, the job cannot be restored. 6 Press [Stop/Reset] to return to the standby display. 7-3 Maintenance CHAPTER 8 This chapter explains how to clean the machine, replace the toner cartridge, and repack and transport the machine. Periodic Cleaning Your machine requires little periodic maintenance. This section describes the necessary cleaning procedures for your machine. CAUTION · When cleaning the machine's exterior or the platen glass, be sure to disconnect the power cord before cleaning the machine. · For the MF5750/MF5770 models, print any received faxes stored in the memory before disconnecting the power cord, since the documents in the memory are backed up only for about 3 minutes. · Do not use tissue paper, paper towels, or similar materials for cleaning; they can stick to the components or generate static charges. Use a soft cloth to avoid scratching the components. · Never use volatile liquids such as thinner, benzene, acetone, or any other chemical cleaner to clean the interior of the machine; these can damage the machine's components. Cleaning the Exterior Wipe the machine's exterior with a clean, soft, lint-free cloth moistened with water or diluted dishwashing detergent solution. Cleaning the Scanning Area Wipe the scanning area (shaded area) with a clean, soft, lint-free cloth moistened with water, then wipe with a clean, soft, dry, lint-free cloth. Platen glass cover Platen glass 8-1 Cleaning the ADF Area Black lines may appear in copies when the ADF is used to feed documents. This is caused by paste, ink, correction fluid, or other foreign matters in the read area of the platen glass (shaded area). Take particular care to clean at the locations where the black lines are appearing on copies. If you have trouble getting the glass clean, wipe with a cloth moistened with water or a mild neutral detergent, and then wipe the glass dry with another cloth. Paste, ink, correction fluid, etc. Read area White roller 8 Maintenance Black lines Copy IMPORTANT · Paste, ink, correction fluid, and other foreign matter can soil the platen glass when you send a document through the ADF while the paste, ink, or correction fluid on the document is still wet. Whenever you load a document in the ADF, always check to make sure that any paste, ink, or correction fluid that is on the document is completely dry. When cleaning the read area of the platen glass, take care not to damage the white roller located on the center of the ADF. · 8-2 When to Replace the Cartridge The cartridge is a consumable item and should be replaced when the toner runs out. If white streaks or light bands appear on the printouts, the toner is running low. Paper feeding direction NOTE Before handling the cartridge, see the precautions in "Handling and Storing the Cartridge, " on p. Rock the cartridge 5 or 6 times to distribute the toner evenly. 8 Maintenance 3 4 Reinstall the cartridge in the machine. Make a few test copies. If the copies appear normal: You can keep using the cartridge. However, a new one will be needed soon. If white streaks or light bands are still present: Replace the cartridge with a new one. For details on how to replace the cartridge, see "Replacing the Cartridge, " on p. 8-6. 8-3 Print Yield This section describes the approximate number of printouts that can be made per cartridge. Approximate Print Yield Canon Cartridge EP-27: Approx. * The term "A4 at 4% dot coverage" denotes a document on which the area covered with toner is 4% of the total area of an A4-size sheet. · The actual number of printouts that can be made per cartridge depends in part on the exposure setting, room temperature, and humidity. · If you print a large number of documents which contain heavy print or many photographs, toner consumption will increase, and white streaks will appear on printouts sooner than indicated above. [. . . ] TEXT/PHOTO: Text/photo mode TEXT: Character mode PHOTO: Photo mode Sets how the exposure is adjusted. The preset copy ratios will change when the paper size group is changed. If the paper size group is changed, the preset copy ratios will also change. Preset copy ratios: 50%, 70%, 100%, 141%, 200% Preset copy ratios: 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% Preset copy ratios: 50%, 64%, 78%, 100%, 129%, 200% The sharpness setting of an image can be adjusted. [. . . ]