User manual CANON ES900 BROCHURE

[. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] 4-2 User Mode Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 How to Set the User Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Chapter 4 User Modes 1. About the User Modes You can configure the scanner settings with the user modes described below. User Mode Functions User mode functions are as follows: ■ Count Only Mode C o u n t O N O n l y M o d e [ O F F ] • When using the Long Document mode, jam detection may not work propery and document may be damaged. • When scanning a document that is 17" (432 mm) or more in length, load the document one page at a time and scan. ■ Stand-by Mode S t a n d - b y M o d e 2 4 0 6 0 [ 1 0 ] ON: Counts the number of pages in a document using stand-alone scanner operations. 3-21. ) OFF: Normal Mode (default) ■ Long Document Mode L o n g D o c u m e n t O N [ O F F ] 240: Scanner enters Stand-by Mode after 4 hours of nonuse. 10: Scanner enters Stand-by Mode after 10 minutes of non-use (default). ■ Display Language Mode J a p a n e s e O N [ O F F ] ON: Enables detection of documents up to 24. 8" (630 mm) long for auto document size detection. 3-2. ) OFF: Enables detection of documents up to 17. 0" (432 mm) long for auto document size detection (default). IMPORTANT • Processing speed may slow down when scanning while the Long Document mode is set. • When scanning two-sided documents with the Long Document mode set to ON, the documents will be scanned one side at a time, regardless of the single-pass duplex setting. • When using the Long Document mode, if you place a long document askew in the document tray, it will rub against both sides of the feeding path and may damage the document. Make sure to align the document straight when placing it in the document tray. ON: Japanese OFF: English (default) ■ Display Contrast Setting D i s p l a y C o n t r a s t Use the and keys to move the pointer ( ) to the left for lighter contrast or to the right for darker contrast. 4-2 Chapter 4 User Modes ■ Setting SCSI Transfer Speed S C S I S p e e d [ 2 0 ] 1 0 5 ■ Total Counter T o t a l C o u n t e r 0 Set the maximum value for synchronous transfer speed for the SCSI interface. 20: 20 Mbyte/sec (Ultra SCSI) (default) 10: 10 Mbyte/sec (First SCSI) 5: 5 Mbyte/sec (non-synchronous) If the scanner does not operate correctly when the output speed is set to ‘20’ Mbyte/sec, reduce the transfer speed to ‘10’ Mbyte/sec or ‘5’ Mbyte/sec. Displays the cumulative total number of document pages fed by the scanner. How to Set the User Modes Use the following procedure to configure user mode settings. 1. Press Menu to display the user mode screens. ■ Setting USB Short Packet U S B S h o r t P a c k e t [ O N ] O F F Change the USB short packet settings. • Cleaning paper: Attach the cleaning paper to the scanning area cleaning tool located behind the pressure board. 5-11. ) Cleaning the Main Unit Wipe the scanner with a firmly wrung cloth moistened slightly with water or mild detergent. Then wipe off with a clean, dry cloth. 5-4 Chapter 5 Maintenance 2. Wipe the flatbed (platen glass), scanning glass (narrow strip of glass) and pressure board with a cloth moistened with plain water and thoroughly wrung out. Next, wipe the flatbed (platen glass), scanning glass and pressure board with a soft, dry cloth. Cleaning the Flatbed (Platen Glass) and Pressure Board A dirty flatbed (platen glass) or pressure board can cause soiling of scanned images, or document size detection errors. Clean the flatbed (platen glass) and pressure board periodically. 1. Open the feeder. CAUTION Open the feeder carefully and slowly, taking care to avoid letting the feeder fall over backwards. 5-5 Chapter 5 Maintenance 3. Slowly and carefully close the feeder. Cleaning the Feeder Without periodic cleaning, a problem may be caused on the scanned image or the document may become soiled. Open the feeder cover. Operate the opening lever, and then slowly raise the cover until it stops. CAUTION Lower the feeder slowly, taking care to avoid pinching your fingers. Wipe the 13 rollers inside the feeder cover with a cloth moistened with plain water and thoroughly wrung out. Next, wipe the rollers dry with a soft, dry cloth. 5-6 Chapter 5 Maintenance 3. [. . . ] Set [Document Orientation] to [90 degrees] and [Duplex Orientation] to [Calendar type] in the Orientation Settings dialog box. ■ Scanning documents longer than 17. 0" (432 mm) (Long Document Mode) When you want to scan a document that is longer than 17. 0" (432 mm), you can enable [Long Document Mode] in the scanner settings and set the page size setting to [Auto-detection] in order to scan documents up to 24. 8" (630 mm) long. 1. In User Mode, set [Long Document Mode] of the scanner settings to [ON]. Select the [Text Orientation Recognition] check box in the Advanced Settings dialog box. 2. Set [Page Size] to [Auto-detection] in the Basic Setup dialog box. IMPORTANT • Long Document Mode is not available if it is not supported by the application program. [. . . ]