User manual BREVILLE BKE200

[. . . ] · Do not place this appliance on or near a gas burner or electric element, or where it could touch a heated oven. · Keep the kettle clear of walls, curtains and other heat or steam sensitive materials. · Always ensure the kettle is properly assembled before connecting to a power outlet and operating. [. . . ] Return the entire appliance to the nearest authorised Breville centre for examination and/or repair. · Any maintenance other than cleaning should be performed at an authorised Breville Service Centre. · The installation of a residual current device (safety switch) is recommended to provide additional safety protection when using electrical appliances. It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance. See your electrician for professional advice. do Not operAte tHe AvANCe® 2 lItre Cordfree kettle oN AN INClINed SurfACe. tHIS kettle SHould Be uSed WItH A reSIduAl CurreNt devICe (SAfety SWItCH) to leSSeN tHe rISk of SCAldINg or otHer INJury from Hot WAter tHAt mAy Be eJeCted If tHe HeAtINg elemeNt eruptS. dISregArd tHIS poINt If your Home IS fItted WItH A reSIduAl CurreNt devICe (SAfety SWItCH). 5 4 know your Breville Avance® 2 litre Cordfree kettle operating your Breville Avance® 2 litre Cordfree kettle Before fIrSt uSe 4. The kettle will automatically switch to the OFF position when the water has boiled. Take care to hold the kettle level, especially when filled to the maximum (MAX) level. To re-boil it may be necessary to wait for a few seconds to allow the control to reset. If further heating of the kettle is not required, switch off at the power outlet, unplug the power cord and empty the water from the kettle. Replace the kettle onto the power base and close the lid. Thiskettlemustbeusedwiththepowerbase supplied. Usecautionwhenpouringwaterfromyour kettleasboilingwaterandsteamwillscald. Donot pourthewatertooquickly. On / Off switch with safety auto cut off and boil dry protection Safety locking hinged lid Remove and safely discard any packaging material or promotional labels before using your kettle for the first time. It is recommended before the first use to fill the kettle to the maximum level with cold tap water, bring to the boil then discard the water. Your kettle will only operate when positioned on the power base with the ON/OFF switch in the `ON' position. The kettle will automatically switch `OFF' once the water has boiled. Removable scale filter operAtIoN of your kettle . To fill the kettle with water, remove it from the power base and open the lid by pulling back the lid release latch. Plug the power supply cord into a 230/240V power outlet and switch `On'. The power ON light will illuminate. Alwaysfillthekettlewithwaterbetweenthe minimum(MIN)andmaximum(MAX)markson thewaterwindowonthekettle. Toolittlewater willresultinthekettleswitching. Fillingabovethe maximummark(MAX)mayresultinboilingwater splashingfromthekettle. 2 Litre capacity WArNINg: do Not opeN tHe lId durINg ANd After operAtIoN. [. . . ] Clean spout by using a cloth dampened with Breville Kettle Cleaner, rub well. Then wipe off. Theconcealedelementinthebaseofthekettleis madefromhighqualitystainlesssteel. Anybrown stainsappearingaretheresultofmineraldeposits andarenotrust. 5. Fill kettle with fresh water and bring to the boil, discard boiled water. [. . . ]