User manual BOSCH MFQ 3540/04

[. . . ] There is a major possibility of accidents if you mistakenly happen to turn off the safety device of the appliance! · · 4 5. Assembly All accessories are coated with a thin oil film to protect them from corrosion. Therefore clean all the parts carefully before using the appliance for the first time, in accordance with the detailed instructions found under "8 Cleaning". There you will find the step-by-step illustrations for assembling the appliance. [. . . ] After everything has been assembled correctly, screw on the ring clamp tightly. 5. Assembly · The assembled meat grinder is connected by a bayonet joint to the motor block : - Insert the meat grinder into the motor block. The arrow on the mincer casing should be on the symbol "offen" (open) (Fig. Turn the stuffing funnel of the meat grinder upwards till it is vertical (Fig. - To take it out, once again press down the meat grinder lightly and turn the stuffing funnel in the direction of the symbol "offen" (Fig. on GB b) Fixing the sausage stuffer attachment Once the meat grinder has been assembled as described under a): · · Turn open the ring clamp and . . . Replace the cutting disc with the sausage disc . Now place the sausage stuffer attachment µ in front of the sausage disc, . . . before screwing on the ring clamp tightly. · · · 5 c) Fixing the kubbe attachment Once the meat grinder has been assembled as described under a): GB · · Turn open the ring clamp and . . . · Replace the cutting disc with the two plastic parts of the kubbe attachment ¸. When everything has been attached correctly, screw on the ring clamp tightly. To remove once again press in the grater funnel lightly and turn it in the direction of the symbol "open" (Fig. Now you can take out the grater funnel. e) Fixing the shortbread cookie attachments Once the meat grinder has been assembled as described under a): · · · Turn open the ring clamp take out the cutting disc cross blade . and the · d) Fixing the grater and cutter attachments When the meat grinder has been removed from the motor block: · First select the appropriate attachment. · The sausage mixture will be pressed into the sausage skin by the sausage stuffer. When it is long enough switch off the device and press together the sausage at the end and turn it around its longitudinal axis. Therefore it is best not to overstuff the sausage to prevent it from splitting. · After you have read all the instructions about the topic "Sausage", you can use the machine as described under 6 a). d) Grating and cutting After you have placed the food to be grated into the feeding tray : · · Push them with the square stodger into the feeding tube ¹. If some food is stuck on the grating attachments: Switch off the device before removing the attachments or reaching in to clean them. After you have read all the instructions about the topic "Grating and cutting", you can use the machine as described under 6 a). GB · · · e) Using the kubbe attachment With the kubbe attachment foodstuffs can be processed to form hollow rolls of meat or vegetables, which can then be stuffed as desired. · Put the meat through the meat grinder twice before pressing it through the kubbe attachment. After you have read all the instructions about the topic "Kubbe attachment", you can use the machine as described under 6 a). · f) Making shortbread cookies After you have made the shortbread dough according to your recipe, and after having fixed the shortbread cookie attachment: · Line a small baking tray with greaseproof paper and place or hold it directly under the opening in the front of the appliance. 8 · Press dough evenly into the feeding tube ­ the transport screw pushes it through the design on the pattern strip of the shortbread cookie attachment . After you have read all the instructions about the topic "shortbread cookie attachment", you can use the appliance as described under 6 a). · · In case this does not work, wait for a further 15 minutes. If it still does not function at the end of this period, this indicates a technical problem. GB · If themains cable is damaged or or the accessories are visibly damaged: · · · Switch off the device by pressing the OFF button! [. . . ] If you do not succeed by doing so, clean the machine as described under 8. In this way accidents caused by the unexpected switching on of the machine and electric shocks can be prevented. a) Cleaning the Motor block · Clean the external surfaces and the power cord with a slightly damp cloth. Otherwise one could get a life threatening electric shock, if moisture, which has crept in, touches the electrical wiring. · · If the motor stops suddenly, it could be due to the internal overload warning device, which automatically turns off the machine when overloaded. [. . . ]