User manual BONTRAGER AEROBAR

[. . . ] Regularly inspect your handlebar for signs of fatigue stress: dents, cracks, scratches, deformation, or discoloration. As an example, a crash may add a great deal of extra stress to your bike. If you choose to jump your bicycle, use it for stunts, or ride it after a crash, carefully inspect your handlebar for signs of fatigue before and after each ride. If you are unsure of the safety of your Bontrager Carbon Aerobar, do not ride the bicycle; take the bicycle to your dealer for adjustments. [. . . ] If your hands, arms, or shoulders are uncomfortable or numb you may need to adjust the handlebar or select components more suitable to your personal needs; consult your dealer. WARNING An improperly adjusted or tightened handlebar or stem may allow the handlebar to move unexpectedly, which can cause you to lose control and fall. Make sure the stem, handlebar, aero extension, and handlebar parts are positioned and tightened properly before riding the bike. To adjust the angle of the handlebar 1. Loosen the handlebar clamp bolt(s) on the stem just enough that the handlebar can be rotated in the stem. Position the handlebar to the desired angle, making sure they are centered in the stem. Tighten as in Inspect your handlebar regularly. To adjust the length of the aero extensions 1. Loosen the aero extension clamp bolt(s) on the handlebar just enough that the extensions can be moved. Position the extensions to the desired length, making sure the ends of the extensions are within the clamp area (Figure 3). Tighten as in Inspect your handlebar regularly. To adjust the width of the elbow pads 1. Reinstall the bolts, and tighten as in Inspect your handlebar regularly. To change the handlebar height Adjusting the handlebar height on a direct-connect stem affects the headset bearing adjustment. This procedure requires special tools and training so this should only be done by your dealer. Figure 3- Do not over-extend the aero insertion; the minimum insertion decal must remain exposed behind the clamp Carbon Aerobar installation instructions These instructions are written for an experienced mechanic. If you are not sure of your ability to correctly install this handlebar, or do not have the proper tools for installation, have the handlebar installed by your Bontrager dealer. To remove the old handlebar 1. 6. Use an allen wrench to loosen the clamp screws on the control levers. Remove the handlebar from the clamp. To install the Carbon Aerobar 1. Make sure the gaps at the top and bottom of the stem face plate are even. To install the aero extensions 1. Position the extensions to the desired length, making sure the ends of the extensions are within the clamp area (Figure 3). Tighten as in Inspect your handlebar regularly. To install the control levers and bar tape Make sure no part has burrs or deformations which could scratch or damage the handlebar. Slide the levers into position on the handlebar and connect the cables. Tape the control cables to the handlebar with plastic or electrical tape. [. . . ] Before adding or changing any part of your bike, consult your dealer. Bontrager Carbon Aerobar crash replacement policy Assessing any damage done to a carbon fiber part requires more experience than is needed to inspect metal parts. If you crash your bike and the main force of the impact is absorbed by the handlebar, we strongly encourage you to replace the bar, even if there are no visual indications of damage. If this crash occurs within one year from the date of retail purchase, Bontrager offers a crash replacement program, substantially reducing replacement cost. To take advantage of this program, contact us using the information listed above, and ask for the Warranty department. Bontrager Limited Warranty Trek Bicycle Corporation warrants each new Bontrager component against defects in workmanship and materials. This warranty covers· · · · This warranty does not cover- Bontrager Carbon Aerobar for the a period of one year from the date of sale. Normal wear and tear Improper assembly Improper follow-up maintenance Installation of parts or accessories not originally intended for, or compatible with the component as sold · Damage or failure due to accident, misuse, abuse, or neglect · Labor charges for part replacement or changeover This warranty is void in its entirety by any modification of the component or its parts. [. . . ]