User manual ASUS P6000

[. . . ] AP6000 Dual Pentium® II Server Hardware Reference Guide USER'S NOTICE No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. [. . . ] Open the front door and side panels to install final server components, such as CPU, Memory, Hard Disk Drives, expansion cards. Use this hardware reference guide along with your motherboard manual in order to make these installations. Connect server to network (an optional network card is needed) WARNING: To prevent electrical shock or fire, be sure not to plug telecommunications/telephone cables into the network RJ45 connector in the server if one is installed. Connect Server to AC power - The power supply will automatically detect and adjust to 120VAC or 240VAC power. WARNING: This server is designed for connection to a grounded (earthed) outlet. To reduce the risk of electrical shock or damage to your server, do not bypass the grounding plug. AP6000 Hardware Reference Guide I. Introduction Turn on the system unit by turning the power knob clockwise and pushing inwards momentarily. The power button will snap back because ATX power systems have a electrical On/Off switch unlike AT systems which require a permanent On or Off position. If the power indicator does not light, make sure the power cord is connected to the system unit and to a working grounded outlet. Components When booting your server for the first time, hold the "Delete" key and enter BIOS setup in order to make settings. ISA cards requires that you set "IRQ XX Used by ISA : Yes" in BIOS PNP AND PCI SETUP in order for that IRQ to be reserved for your ISA expansion card. You need to set "Boot Sequence : A, C" in BIOS FEATURES SETUP in order to boot from a floppy diskette to setup your hard disk. Insert a bootable floppy diskette and select "Save & Exit Setup" from the BIOS main menu. Once your server has properly booted, an "A:\>" prompt will appear. Replace your boot disk with a RAID setup diskette and setup your RAID. Reboot your server with the operating system boot disk in order to install drivers for your devices (such as CD-ROM and SCSI devices) and install your server operating system. You may be prompted for manufacturer supplied driver diskettes for each device on your server if they are not included in the operating system setup drivers. NOTE: Non-RAID hard disk drives can be setup using boot diskettes provided with the server operating system or with MSDOS "FDISK. EXE". You must have the motherboard or other SCSI device driver diskettes when prompted by the operating system setup. System Components The front side of the server is provided to show the front exterior components of this server. The chassis is made of strong rust-resisting metal and covered with a protective ivory surfacing. ATX Power Button This server uses an ATX power supply. Turn the power switch clockwise and push in momentarily to turn on or turn off the power. [. . . ] Devices normally come with its termination enabled by jumpers or dip switches. You must disable these termination for devices in between the ends. II. Components SCSI Information 24 SCSI ID Jumpers All SCSI devices, including this motherboard with onboard SCSI, must have a SCSI identification number that is not in use by any other SCSI device. The SCSI ID serves two purposes: · · It uniquely defines each SCSI device on the bus. [. . . ]