User manual ASUS M2V890

[. . . ] V-Series M2V890 ASUS PC (Desktop Barebone) E2747 First Edition V1 September 2006 Copyright © 2006 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Keep the cap on pins 2-3 for about 5-10 seconds, then move the cap back to pins 1-2. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! CLRTC 12 Normal (Default) 23 Clear CMOS Clear RTC RAM · You do not need to clear the RTC when the system hangs due to overclocking. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values. Due to the chipset limitation, AC power off is required prior using C. P. R. You must turn off and on the power supply or unplug and plug the power cord before reboot the system. · ASUS V-Series M2V890 4-3 3. Keyboard power (3-pin KBPWR) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press a key on the keyboard (the default is the Space Bar). This feature requires an ATX power supply that can supply at least 500 mA on the +5VSB lead, and a corresponding setting in the BIOS. KBPWR 2 1 +5V (Default) 3 2 +5VSB Fan connectors 4. 4 1. Connectors Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive. Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5. FLOPPY NOTE:Orient the red markings on the floppy ribbon cable to PIN1. PIN1 Floppy disk drive connector 4-4 Chapter 4: Motherboard info 2. Serial ATA connectors (7-pin SATA1, SATA2) These connectors are for the Serial ATA signal cables for Serial ATA hard disk and optical disk drives that allows up to 150 MB/s data transfer rates, faster than the standard parallel ATA with 133 MB/s (Ultra DMA133). If you install Serial ATA hard disk drives, you can create a RAID 0, RAID 1, and JBOD configuration through the onboard VIA® VT8237R Plus controller. GND RSATA_TXP2 RSATA_TXN2 GND RSATA_RXP2 RSATA_RXN2 GND SATA2 GND RSATA_TXP1 RSATA_TXN1 GND RSATA_RXP1 RSATA_RXN1 GND SATA1 SATA connectors Install the Windows® 2000 Service Pack 4 or the Windows® XP Service Pack1 before using Serial ATA. · · For detailed instructions on how to configure RAID 0, 1, and JBOD, refer to the RAID manual in the support CD. The RAID function of these connectors is set to [Disabled] by default. See section "5. 4. 4 Onboard Device Configuration" for details. ASUS V-Series M2V890 4-5 3 IDE connector (40-1 pin PRI_EIDE) The onboard IDE connectors are for Ultra DMA 133/100/66 signal cable(s). There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device(s). SEC_IDE NOTE:Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN1. PRI_IDE PIN1 IDE connectors Drive jumper setting Single device Two devices Cable-Select or Master Cable-Select Master Slave · Mode of device(s) Master Slave Master Slave Cable connector Black Black Gray Black or gray Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices. · If any device jumper is set as "Cable-Select", make sure all other device jumpers have the same setting. 4. CPU Fan Connectors (4-pin CPU_FAN) The fan connectors support cooling fans of 350mA~740mA (8. 88W max. ) or a total of 1A~2. 22A (26. 64W max. ) at +12V. Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector. 4-6 Chapter 4: Motherboard info PIN1 CPU_FAN CPU FAN PWM CPU FAN IN CPU FAN PWR GND Fan connectors Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. Do not place jumper caps on the fan connectors! 5. USB connectors (10-1 pin USB56, USB 78) These connectors are for USB 2. 0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. USB_P6+ GND USB_P8+ USB_P7+ USB_P6- USB_P8- USB+5V USB+5V GND GND NC USB56 USB+5V USB_P5+ GND USB_P5- USB78 USB+5V USB_P7- USB connectors Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! The USB module is purchased separately. ASUS V-Series M2V890 NC 4-7 6. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for an ATX power supply. The plugs from the power supply are designed to fit these connectors in only one orientation. [. . . ] The Supervisor ESC Exit The message "Password Installed" appears after you successfully set your password. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message "Password Uninstalled" appears. If you forget your BIOS password, you can clear clear it by erasing the CMOS Real Time Clock (RTC) RAM. [. . . ]