User manual AOC LM914

[. . . ] The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. 1. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Refer servicing to qualified personnel only. 1 LM914 PRECAUTIONS ! [. . . ] A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0. 75mm!Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0. 75mm!) shall be used. 5 LM914 INSTALLATIONS INSTRUCTIONS (cont) PREPARING TO INSTALL THE CABLES 1. Remove the cable cover. INSTALLATIONS INSTRUCTIONS (cont) 6 LM914 CABLE CONNECTIONS 1 ­ Connect the DC-jack power cable into DC-IN connector on the back of the monitor. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. (Optional ­ Requires a video card with DVI port) Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer's DVI port. (Optional) - Connect the audio cable between the monitor's audio input & the computer sound card's audio output (green port). Connect the female end of the power cord to the monitor's power adapter and connect the male end of the power cord to the AC outlet. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). (Optional ­ Headphone not included) ­ Connect a headphone to the monitor's headphone jack. Figure 2 - Connecting Cables 1. Power Cord Headphone (Not Included) INSTALLATION INSTRUCTIONS (cont) 7 LM914 Preparing To Install The Optional Wall Mount Arm (Not Included) CONNECTIONS This monitor can be attached to a wall mounting arm or bracket you can purchase separately from Ergotron (www. ergotron. com). Turn the power OFF then dis-connect the cables from the monitor before performing the procedure below. Remove the base. INSTALLATION INSTRUCTIONS (cont) 8 LM914 Attaching The Optional Wall Mount Arm (not supplied) Follow these steps to finish installing the wall mounting arm: 1. Line up the holes of the arm with the holes in the back of the monitor. Refer to the user's manual that came with the optional wall mounting arm for instrucstions on attaching it to the wall. ADJUSTING THE VIEWING ANGLE INSTALLATION INSTRUCTIONS 9 LM914 · For optimal viewing it is recommended to look at the full face of the · · monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5° to 20°. Figure 3 NOTES · Do not touch the LCD screen when you change the angle. Careful attention is required not to catch your fingers or hands when you change the angle. 10 LM914 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the side of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power indicator will light up. Figure 4 - External Control Button EXTERNAL CONTROLS 1. Power Indicator Power Button Headphone Jack Volume Control 11 LM914 FRONT PANEL CONTROL · Power Button: Press this button to switch the monitor's power ON or OFF. · MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness/Contrast OSD status. · Brightness · Contrast /: Adjust brightness or function adjust. : Adjust contrast or function adjust. / · Auto Adjust button / Exit: 1. [. . . ] Then look for "Installing the Driver" section. 20 LM914 APPENDIX SPECIFICATIONS Driving system Size Pixel pitch Viewable angle Response time Video Separate Sync. H-Frequency V-Frequency TFT Color LCD 48cm(19. 0") 0. 294mm( H )x 0. 294mm( V ) 170° (H) 170° (V) 25 ms ( Typical ) R, G, B Analog Interface H/V TTL 24KHz ­ 93KHz 55-85Hz 16. 7M Colors 135MHz 1280 x 1024 @85Hz TM VESA DDC1/2B <60W <5W D-Sub 15pin Analog:0. 7Vp-p(standard), 75 OHM, Positive DVI 24pin Digital sigal Horizontal : 376. 32mm Vertical : 301. 056mm 12VDC/5. 0A 60W Max Operating Temp: 0° to 40°C Storage Temp. : -10° to 50°C Operating Humidity : 20% to 90% 5. 9Kgs Unit (net) LCD Panel Input Display Colors Dot Clock Max. Resolution Plug & Play EPA ENERGY STAR® Input Connector Input Video Signal Input Connector Input Video Signal Maximum Screen Size Power Source Environmental Considerations ON Mode OFF Mode Weight (N. 00 LM914 Switch Auto Adjust Key / Brightness / Contrast Power Button MENU/ Exit Volume Contrast Brightness Input Selected Focus Clock H-Position V-Position Auto-center Language Scaling Mode C1 ( 6500°K ) C2 ( 7800°K ) RGB Color temperature Recall Exit 60 Watts 2W + 2W rms (Stereo) UL, CSA, FCC, TÜV/GS, CE, ISO13406-2, Windows XP Logo External Controls: Functions · · · · · · · · · · · · · · · · · · · · · Power Consumption Audio Regulatory Compliance ( Maximum ) 22 LM914 FACTORY PRESET TIMING TABLE HORIZONTAL FREQUENCY 31. 47kHz 31. 47kHz 31. 47kHz 31. 47kHz 35. 00kHz 37. 50kHz 37. 86kHz 37. 879kHz 46. 875kHz 35. 16kHz 48. 01kHz 49. 725kHz 48. 363kHz 56. 476kHz 60. 021kHz 64. 000kHz 80. 000kHz 91. 146kHz 79. 976kHz 60. 000kHz 80. 000kHz VERTICAL FREQUENCY 70. 0Hz 70. 0Hz 70. 0Hz 60. 0Hz 66. 6Hz 75. 0Hz 72. 0Hz 60. 0Hz 75. 0Hz 56. 0Hz 72. 0Hz 75. 0Hz 60. 0Hz 70. 0Hz 75. 0Hz 60. 0Hz 75. 0Hz 85. 0Hz 75. 0Hz 60. 0Hz 85. 0Hz STANDARD Dos-mode Dos-mode Dos-mode VGA RESOLUTION 640 × 400 720 x 400 720 x 400 640 × 480 640 × 480 640 × 480 640 × 480 800 × 600 SVGA 800 × 600 800 × 600 800 × 600 832 × 624 1024 × 768 XGA 1024 × 768 1024 × 768 1280 × 1024 1280 × 1024 SXGA 1280 × 1024 1152 × 864 1280 × 960 1280 × 960 Note: The factory preset mode for DOS is 720x400 @70Hz. 23 LM914 CONNECTOR PIN ASSIGNMENT 1 6 11 5 10 15 15 - Pin Color Display Signal Cable PIN NO. [. . . ]