User manual AEG-ELECTROLUX WESTINGHOUSE LTV-19W6

[. . . ] Do not place your LCD near basins or sinks where it may come in contact with water. Never place heavy or sharp objects on the LCD display, video cable, or power cord. Overloading Outlets Do not overload electrical power sources when installing television. Overloading wall outlets, circuits, or extension cords can result in overheating, fire, or electric shock. [. . . ] Align the holes and tabs, press and snap the base stand into place. Detachable Base Stand To detach the base stand, just press on the locking tabs on the bottom of the base stand and remove the base stand from the stand neck. 7 3. Connect Antenna, Video, S-Video, YPbPr, DVI, and VGA Cables Connect video and audio cables from compatible devices to the back panel of the LCD TV. Video Inputs PC Inputs Video Inputs PC Inputs S- Video Audio-R Audio-L Video DVI YPbPr Antenna Audio-In Audio-Out D-Sub (VGA) 8 Note: The Audio-L and Audio-R (Audio L/R) inputs are shared between YPbPr, S-Video, and Video source input connectors. Connecting a computer to the LCD TV: IMPORTANT: Before you begin, make sure the computer and TV are turned off. Connect a D-Sub (VGA) or DVI cable and an audio cable to the back of the LCD TV. D-Sub CONNECTION: Connect an analog D-Sub (VGA) cable from your computer VGA port to the D-Sub input connection. Connect a 3. 5mm stereo mini-cable from the computer's AUDIO OUT port to the AUDIO IN port on the LCD TV. DVI-D CONNECTION: Connect a Digital DVI cable from your computer to the DVI-D input connection. Connect a 3. 5mm stereo mini-cable from the computer's AUDIO OUT port to the AUDIO IN port on the LCD TV. After you turn on the computer, the TV will automatically adjust to the resolution of the computer. Set the computer timing mode to 1440 x 900 at 60Hz, then turn off and reboot the computer. Refer to your computer's graphic card user guide for questions on how to set this timing mode. 9 4. Connect Power Cable Connect the power cord to the back of the LCD TV and then into a properly grounded AC outlet. 5. Turn Power On Press the power button on the right side of the LCD TV or on the remote control to turn on the TV. Power Button Remote Power Button 10 6. Programming TV Channels 1. Select TV as the source input using the Source button on the remote control. Once the CH Auto Scan is complete, switch channels by using the CH / arrow keys on the remote. Use the , or to add or erase the selected channel. 11 Controls & Connections This section describes the keypad panel controls, and remote control in more detail. Front View of the Product Use the buttons on the right side keypad control to display and adjust the On Screen Display (OSD). The OSD controls are explained at the next page and are defined in the "OSD Functions" section. IR Receiver Keypad Controls Speakers 12 Side Keypad Controls 1 2 3 4 5 6 Button 1 2 3 Mode CH+ CHVolVol+ TV Source Channel up Channel down Volume down OSD Menu Navigate up Navigate down Decrease value 4 Volume up Increase value 5 6 Press and hold for 2 seconds to Menu/Source access the OSD menu. Power TV ON or OFF Enter/Exit Menu TV ON or OFF 13 Remote Control 1. MTS (Multi-channel TV Sound) Stereo, Mono and SAP sound selection 1 3. PIP Available in D-Sub/DVI Modes; to turn PIP picture on & off and select PIP picture size. PIP Menu 10 Used to navigate through the PIP OSD menu and control audio swap. CH/ Channel Up/Down adjustment; also available on key controls and OSD menu. Vol/ Volume Up/Down adjustment; also available on key controls and OSD menu control. CC Set Closed Caption and Text modes toggle through OFF, CC1, CC2, CC3 etc. Exit Exit the OSD menu. 3 4 9 12 13 14 16 17 14 OSD Functions This section describes each on-screen display (OSD) command. There are different OSD menus depending on whether you are in TV, Video (Video/S-Video/YPbPr) or PC (D-Sub/DVI) mode. [. . . ] Plug another electrical device (like a radio) to the power outlet to verify that the outlet is supplying the proper voltage. If any colors (red, green, or blue) are missing, check the video cable to make sure it is securely connected. Loose or broken pins in the cable connector could cause an improper connection. The red connector for right audio is easily confused with the red Pr connector in YPbPr component video input. [. . . ]