User manual AEG-ELECTROLUX T57860

[. . . ] Tips and information about economical and ecological use of the machine are marked with the clover symbol. Should any problems arise, this booklet provides instructions on how to solve them by yourself; see section "Something not working?". If this information is not sufficient, please contact our nearest Service centre (address and telephone numbers are indicated on the enclosed leaflet). Printed on recycled paper. People who think ecologically, act accordingly. . . 2 125985010 gb. qxp 2006-06-12 13:15 Page 3 Contents Operating Instructions. [. . . ] (The laundry should be taken out towards the end of the crease guard phase at the latest to prevent creases from forming. ) 1. It is best to use a damp hand for this purpose (refer to "Cleaning and maintenance" section). After each drying cycle ­ clean the micro-fine filter and fine strainer, ­ drain the condensate tank (refer to the "Cleaning and maintenance" section). Close loading door. 14 125985010 gb. qxp 2006-06-12 13:16 Page 15 Cleaning and maintenance Cleaning fluff filter To ensure that the dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be cleaned after every drying cycle. Never operate the dryer without fluff filters or with damaged or blocked fluff filters. Use a damp hand to clean the microfine filter, which is built into the lower part of the loading aperture. 3. It is best to use a damp hand for this purpose. 15 125985010 gb. qxp 2006-06-12 13:16 Page 16 Clean the entire filter area The strainer area does not have to be cleaned after every drying cycle, but should be checked regularly and cleaned of fluff if necessary. To do this, grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets. Press both journals of the large mesh filter into the brackets on the loading door until they snap into place. Press against the large mesh filter until it locks into the interlock. If the fine strainer is not fitted, the large mesh filter will not snap into place and the loading door cannot be closed. Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished. Emptying the water reservoir Empty condensate tank after every drying cycle. If the condensate tank is full, an active programme will break off automatically and the EMPTY WATER display will light up. Laundry must be adequately predrained. Select time programme or Not enough washing loaded higher drying level (e. g. or washing loaded is too INTENSIVE DRY instead of dry for selected programme. Close loading door. Dryer does not work. Loading door is open. Have you pressed the START/ PAUSE button? Press the START/PAUSE button again. 19 125985010 gb. qxp 2006-06-12 13:16 Page 20 Problem Possible cause Remedy Select a different programme the next time you dry Wrong programme selected. Uncover ventilation slots in base area. Residue on inside surface of Clean inside surface of drum or drum ribs. drum and drum ribs. Make an adjustment using the INTENSITY function (see chapter "Drying, Selecting additional functions"). Mains plug disconnected. Loading door does not open with DOOR button. Loading door does not close. When pressing a button, the corresponding button flashes several times. Loading Programme selector in OFF door can be opened at any time by exerting pressure on position. Fine strainer not in place Install fine strainer and/or and/or large mesh filter not snap large mesh filter into locked in place. After Turn the programme knob the start of the programme, to OFF Set the programme the option can no longer be again. Replace light bulb (see next section). PROGRAMME TIME display changes erratically or stays unchanged for a long time. [. . . ] Performing the guarantee means that the appliance is returned to the condition it was in before the defect occurred. So as to avoid more severe damage, the defect must be brought to our attention immediately. Applying the guarantee is subject to the consumer providing proof of purchase showing the purchase and/or delivery date. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic), synthetic materials and rubber, is the result of inappropriate use. [. . . ]