User manual AEG-ELECTROLUX T56845L

[. . . ] The information marked with this symbol provides additional instructions and practical tips on the use of the appliance. Tips and information about economical and ecological use of the machine are marked with the clover symbol. Should any problems arise, this booklet provides instructions on how to solve them by yourself; see section "Something not working?". If this information is not sufficient, please contact our nearest Service centre (address and telephone numbers are indicated on the enclosed leaflet). Printed on recycled paper. [. . . ] After each drying cycle ­ clean the micro-fine filter and fine strainer, ­ drain the condensate tank (refer to the "Cleaning and maintenance" section). 16 125983990. qxp 2006-04-21 07:12 Page 17 Cleaning and maintenance Cleaning fluff filter To ensure that the dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be cleaned after every drying cycle. Never operate the dryer without fluff filters or with damaged or blocked fluff filters. Use a damp hand to clean the microfine filter, which is built into the lower part of the loading aperture. 3. It is best to use a damp hand for this purpose. 17 125983990. qxp 2006-04-21 07:12 Page 18 Clean the entire filter area The strainer area does not have to be cleaned after every drying cycle, but should be checked regularly and cleaned of fluff if necessary. To do this, grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets. Press both journals of the large mesh filter into the brackets on the loading door until they snap into place. Press against the large mesh filter until it locks into the interlock. If the fine strainer is not fitted, the large mesh filter will not snap into place and the loading door cannot be closed. Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished. 18 125983990. qxp 2006-04-21 07:12 Page 19 Emptying the water reservoir Empty condensate tank after every drying cycle. If the condensate tank is full, an active programme will break off automatically and the EMPTY WATER display will light up. In order to continue the programme, the condensate tank must first be emptied. The condensate is not suitable for drinking or for preparing foodstuffs. When pressing a button, the corresponding button flashes several times. Re-programme standard setting for degree of drying (see `Programming options' section). Fine strainer not in place Install fine strainer and/or and/or large mesh filter not snap large mesh filter into locked in place. After Turn the programme knob the start of the programme, to OFF Set the programme the option can no longer be again. Replace light bulb (see next section). Drum light does not work. PROGRAMME TIME display changes erratically or stays unchanged for a long time. Programme time is corrected automatically depenAutomatic process; this is ding on type and volume of not a machine fault. laundry and level of dampness. Programme inactive, EMPTY WATER display illuminated. Condensate tank is full. Empty condensate tank, then start programme with START/PAUSE button. 22 125983990. qxp 2006-04-21 07:12 Page 23 Problem Possible cause Lint filter clogged. INTENSIVE DRY instead of STORAGE DRY). Drying cycle lasts an unusually long time. Note: After around 5 hours the drying cycle ends automatically (see , , Drying cycle complete"). Drying cycle ends Not enough washing loaded shortly after programme or washing loaded is too starts. ted. Changing bulb for inside light Only use a special bulb which is designed specially for dryers. Before replacing the bulb, disconnect the mains plug; with a permanent connection: fully unscrew or deactivate the fuse. Unscrew covering bonnet from above bulb (this can be found directly behind the loading aperture, at the top; refer to "Description of machine" section. ) 2. For reasons associated with safety, the covering bonnet must be screwed down tightly. If this is not done, the dryer must not be operated. 23 125983990. qxp 2006-04-21 07:12 Page 24 Programming options Objective Implementation 1. [. . . ] Refer to the "Programme options" section for how to deactivate the EMPTY WATER display. displacement length: 3m 30 125983990. qxp 2006-04-21 07:12 Page 31 Warranty conditions Great Britain We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. · The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. · The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. [. . . ]