User manual AEG-ELECTROLUX T56647

[. . . ] The information marked with this symbol provides additional instructions and practical tips on the use of the appliance. Tips and information about economical and ecological use of the machine are marked with the clover symbol. Should any problems arise, this booklet provides instructions on how to solve them by yourself; see section "Something not working?". If this information is not sufficient, please contact our nearest Service centre (address and telephone numbers are indicated on the enclosed leaflet). Printed on recycled paper. [. . . ] After each drying cycle ­ clean the micro-fine filter and fine strainer, ­ drain the condensate tank (refer to the "Cleaning and maintenance" section). Close loading door. 16 125983250. qxp 2006-03-21 11:11 Page 17 Cleaning and maintenance Cleaning fluff filter To ensure that the dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be cleaned after every drying cycle. Never operate the dryer without fluff filters or with damaged or blocked fluff filters. Use a damp hand to clean the microfine filter, which is built into the lower part of the loading aperture. \ 3. It is best to use a damp hand for this purpose. 17 125983250. qxp 2006-03-21 11:11 Page 18 Clean the entire filter area The strainer area does not have to be cleaned after every drying cycle, but should be checked regularly and cleaned of fluff if necessary. To do this, grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets. Press both journals of the large mesh filter into the brackets on the loading door until they snap into place. Press against the large mesh filter until it locks into the interlock. If the fine strainer is not fitted, the large mesh filter will not snap into place and the loading door cannot be closed. Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished. 18 125983250. qxp 2006-03-21 11:11 Page 19 Emptying the condensate tank Empty condensate tank after every drying cycle. If the condensate tank is full, an active programme will break off automatically and the EMPTY WATER (RESERVOIR) display will light up. In order to continue the programme, the condensate tank must first be emptied. The condensate is not suitable for drinking or for preparing foodstuffs. After Turn the programme knob the start of the programme, to OFF (UIT). Empty condensate tank, then start programme with START/PAUSE (START/PAUZE) button. Drum light does not work. Programme selector in OFF (UIT) position. Defective light bulb. Programme inactive, EMPTY WATER (RESERVOIR) Condensate tank is full. display illuminated. Select time programme or Drying cycle ends Not enough washing loaded higher drying level (e. g. shortly after programme or washing loaded is too INTENSIVE DRY - INTENSIEFstarts. DRY - KAST-DROOG). 22 125983250. qxp 2006-03-21 11:11 Page 23 Problem Possible cause Lint filter clogged. Note: After around 5 hours the drying cycle ends automatically (see , , Drying cycle complete"). SPECIAL CARE (LAGE TEMP. ) SPECIAL CARE (LAGE TEMP. ) button pressed and load is only suitable for use with volume too big. Laundry must be adequately pre-drained. Changing bulb for inside light Only use a special bulb which is designed specially for dryers. Before replacing the bulb, disconnect the mains plug; with a permanent connection: fully unscrew or deactivate the fuse. Unscrew covering bonnet from above bulb (this can be found directly behind the loading aperture, at the top; refer to "Description of machine" section. ) 2. For reasons associated with safety, the covering bonnet must be screwed down tightly. [. . . ] The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic), synthetic materials and rubber, is the result of inappropriate use. The guarantee cannot be called on for minor faults that do not affect the value or the overall reliability of the appliance. The statutory warranty does not apply when defects are caused by: · a chemical or electrochemical reaction caused by water, · abnormal environmental conditions in general, · unsuitable operating conditions, · contact with harsh substances. The guarantee does not apply to defects due to transport which have occurred outside of our responsibility. [. . . ]