User manual AEG-ELECTROLUX PWE3810-M

[. . . ] Check that the main power supply voltage corresponds to the value indicated on the rating plate on the left side of the appliance. Connect the appliance to an efficiently earthed and correctly installed socket. If the power socket does not match the plug on the appliance, have the socket replaced with a suitable type by a qualified professional. Do not use multiple sockets or extensions. During installation and Use Warning Move the appliance carefully in order not to damage components of the refrigeration circuit and to avoid gas leaks Warning Avoid prolonged exposure of the appliance to direct sunlight Warning When installing the appliance do not over bend hoses After removing the packaging, make sure the product is complete and undamaged and that all components are present. [. . . ] Pressure has to be regulated between 2 and 3 bar operating on the plastic knob. While dispensing ambient water: for pressure increase rotate the knob clockwise, for pressure decrease rotate it counter-clockwise. Once the regulation has been made, push the knob back to its security position. Regulate CO pressure Warning The pressure reducer must be opened only when the connection process is complete and the appliance is powered up Warning When changing CO pressure, the adjusted sparkling level will be reached after dispensing 0. 5 litres of cold sparkling water Warning CO pressure can be adjusted to a maximum of 4 bar 1 CO plastic knob 2 CO pressure gauge CO pressure can be adjusted using the pressure reducer placed on the CO bottle. Pressure has to be regulated 0. 5 bar above inlet water value operating on the CO plastic knob. For pressure increase rotate the knob clockwise, for pressure decrease rotate it counter-clockwise. Dispensing during first start-up During first start-up ambient water is immediately ready. The ice tank will be fully loaded after 5 hours. Usage 17 Dispensing during normal usage Warning Do not insert any object in the ice shards nozzle. This may damage the section with consequent ice melting In order to fill a big bottle or jug, carefully pull out the water dispense nozzle. Place a glass on the drip tray, then select the desired beverage or the ice shards. Dispensing from water nozzle is delayed to prevent accidental leakage. The appliance can dispense 2 litres of cold still or cold sparkling water in 2 hours. The water coolness level may vary if the dispensing time recommendations are not followed. If the ice has been entirely dispensed, fresh ice shards will be available after approximately 40 minutes. The ice tank will be fully loaded after 2. 5 hours. Illumination of the Refreshment Centre For a more comfortable dispensing process, press the light LED of the control panel and switch on the central ambient light. Maintenance and cleaning Warning If the appliance remains switched off for over 8 hours it is necessary to drain the water tank Warning A monthly drainage of the water tank is needed to guarantee the correct quality level Warning Carry out a cleaning of the appliance every six months to ensure the correct quality level Warning Use food grade CO bottle Drainage of the drip tray To prevent water leakage, keep the drip tray clean and dry. 18 Maintenance and cleaning Drainage of the water tank Warning If you had to stop pressing the power icon, please press it again and keep it pressed in order to complete the step Warning After the procedure always remember to close the water discharge tap to avoid water leakage 1. Remove the grid of the drip tray to easily pull out the Refreshment Centre. After extracting the appliance, place the grid back in its original position 3. Place a big container underneath the plastic hose or put the hose in a sink 5. Press the power icon again and keep it pressed until the power LED stops flashing 8. Push back the appliance until it is locked into position Food grade CO bottle replacement Warning While screwing on the new CO bottle, CO leaks might occur Maintenance and cleaning 19 1. Remove the grid of the drip tray to easily pull out the Refreshment Centre. After extracting the appliance, place the grid back in its original position 2. Remove the safety strip of the CO holder to extract the used bottle 3. Secure the new CO bottle to its holder and fix it with the provided safety strip 6. Push back the appliance until it is locked into position Filter cartridge replacement Warning In case of water leakage dry the base carefully Warning Lay a cloth under the filter cartridge to prevent the base from getting wet 1. [. . . ] 25 Pressure has to be regulated between 2 and 3 bar. Check CO pressure Warning Never exceed the indicated inlet value For further information see the chapter on first installation. Pressure has to be regulated 0. 5 bar above inlet water value operating on the CO plastic knob. Water leakage check Warning If water covers the whole base, please turn off the appliance, close the inlet water and call the Assistance. Check if there is water inside the base, especially near water leakage sensors, then dry it carefully. 1 Left rear side water leakage sensor 2 Right rear side water leakage sensor 3 Left middle side water leakage sensor Cold restart Turn off the appliance for 30 minutes, then turn it on again. Environment concerns The symbol on the product or on its packaging indicates that this product should not be treated as household waste. It should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. [. . . ]