User manual AEG-ELECTROLUX PLKU1267DS

[. . . ] Household Beverage Cooler Record Serial/Model Numbers . . . . . . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 2 First Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Energy Saving Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Beverage Cooler Features . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 P/N 297017400 (Oct 2004) This Use and Care Manual provides specific operating instructions for your model. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced when installing, operating, and maintaining any appliance. Record the model and serial numbers in the space provided below. The model and serial number plate is located on the upper left wall inside the beverage cooler. · Destroy or safely discard carton, plastic bags, and any exterior wrapping material immediately after the beverage cooler is unpacked. [. . . ] Remove as many items as needed at one time and close the door as soon as possible. CASTERS CLEANING AND MAINTENANCE CLEANING THE INSIDE · Wash inside surfaces of the beverage cooler with a solution of two tablespoons of baking soda in one quart (1. 136 liters) warm water. Wring excess water out of the sponge or cloth when cleaning in the area of the controls, or any electrical parts. · Wash the removable parts with the baking soda solution mentioned above, or mild detergent and warm water. NEVER use metallic scouring pads, brushes, abrasive cleaners, or alkaline solutions on any surface. DO NOT wash removable parts in the dishwasher. BEVERAGE COOLER FEATURES ADJUSTABLE INTERIOR SHELVES Multi-position adjustable interior shelves can be moved to any position for larger or smaller packages. The shipping spacers that stabilize the shelves for shipping should be removed and discarded. CLEANING THE OUTSIDE Wash the cabinet with warm water and mild liquid detergent. Replace parts. 8 DOOR REMOVAL If door must be removed: · Gently lay the beverage cooler on its back, on a rug or blanket. · To replace door, reverse the above order and securely tighten all screws to prevent hinge slippage. If leaving the beverage cooler door open at any time, make certain that children cannot get into the beverage cooler and become entrapped. PROPER CLEANING OF BEVERAGE COOLER Your beverage cooler's beverage dispensing system needs regular cleaning and sterilization in order to continue serving draft beer with its pure brewery flavor. It is recommended that the delivery lines be cleaned weekly and the entire delivery system cleaned before a new keg is attached. You will need the following parts to clean your unit's dispensing system. These parts are available at any draft beer dispensing equipment supplier. They can be reached at www. micromatic. com or call them toll free at (866) 291-5756. (A) 1 quart Plastic Cleaning Bottle (B) Low Profile Hand Pump (C) Solid Brass Faucet Cleaning Attachment (D) 4 oz. Bottle of Cleaning Solution (E) Faucet Wrench (F) Faucet Cleaning Brush · Mix one gallon of warm water with one ounce of the cleaning solution in a bucket. · Before removing the beverage hose from the tap or from the coupler, make sure the remaining beverage in the delivery line is blown out. This can be done by quickly opening and closing the regulator outlet valve. · Remove the coupler from keg by rotating it counterclockwise. Make sure the canister valve and regulator shut-off valve is shut off before removing the hose. · Remove the faucet from the shank assembly by turning the threaded stainless steel collar clockwise using a faucet wrench. · Disassemble the faucet parts and place in the cleaning solution bucket. · Attach the brass attachment on the end of the cleaning hose to the faucet shank assembly by turning the stainless steel collar counterclockwise. · If the coupler has a shutoff, make sure it is in the open position. · Place the keg coupler in the cleaning solution bucket and pump the cleaning solution through the beer line. [. . . ] · Metal parts undergo expansion and contraction, as in hot water pipes. · Refrigerant (used to cool beverage cooler) is circulating throughout the system. When the surrounding noise level is low, you might hear the compressor running while it cools the interior. Sound will level off or disappear as the beverage cooler continues to run. [. . . ]