User manual AEG-ELECTROLUX MSCOMELECTRONICENGEN

[. . . ] Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc. , which are not a part of the appliance when it was shipped from the factory. Replacement of light bulbs and/or fluorescent tubes (on models with these features). CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY. Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. [. . . ] · External house shading with trees, plants or awnings will help reduce the air conditioner's work load. · Operate heat producing appliances such as ranges, washers, dryers and dishwashers during the coolest part of the day. 4 SZ000302(En)-YaoKong(1018) 4 10/25/2004, 2:33 PM To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. The power supply cord contains a current device that senses damage to the power cord. (On some products this is also indicated by a light on the plug head). Operation of Current Device NOTES: · · · · Do not use this device to turn the unit on or off. The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. It MUST be replaced by one obtained from the product manufacturer. Key Features (On some model) Multi-Step Fan and Cooling Speeds: 90 distinct fan settings give the ultimate in airflow and noise control. Clean Air: An ionic air filtration system that substantially increases the air-cleaning efficiency over conventional air filters. The Clean Air button on the air conditioner Touch Pad ONLY activates this feature. Air Conditioner Features ON/OFF LIGHT ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the touch pad alone or with the remote. ADJUSTS TEMP & TIMES FAN SPEEDS DISPLAYS TEMPERATURE/TIME FAN SPEED ADJUSTS TEMPERATURE OR TIME SETS MODES ACTIVATES TIMER SETS FAN SPEEDS ACTIVATES TIMER REMOTE CONTROL Fig. "A" ON/OFF LIGHT CHECK FILTER RESET BUTTON AUTO COOL FEATURE SLEEP MODE ADJUSTS TEMP & TIMES SETS MODE FAN SPEEDS CLEAN AIR FEATURE (some models) REMOTE TEMP. SENSING INDICATOR (SOME MODELS) TURNS UNIT ON OR OFF SETS MODES ACTIVATES REMOTE THERMOSTAT REMOTE CONTROL w/DISPLAY & REMOTE SENSING BUTTON ACTIVATES TIMER TOUCH PAD Fig. The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on and cooling stars. DO THIS: PRESS MODE BUTTON CHOOSE ENERGY SAVER 7 SZ000302(En)-YaoKong(1018) 7 10/25/2004, 2:33 PM Air Conditioner Features (continued) TIMER: DELAY STOP / START FEATURE YOU WILL SEE: TIMER SETTING LIGHT On Note: For Delay Stop, the unit must be in the On position. DO THIS: Note: For Delay Start, the unit must be in the Off position. PRESS TIMER BUTTON To adjust timer setting, tap or hold the UP arrow(^) or the DOWN arrow(V) to change delay timer at . 5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7. 5, 7, etc. ). The Delay Start mode automatically selects cooling with maximum Fan Speed. To change the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Turning the unit "ON" or "OFF" at any time will cancel the Delay Start/Stop function. SLEEP FEATURE: YOU WILL SEE: LIGHT On DO THIS: PRESS SLEEP BUTTON Note: In this "MODE" the selected temperature will increase by 2 degrees F 30 minutes after the mode is selected. The temperature will then increase by another 2 degrees F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the "Sleep" MODE and the unit will continue to operate as originally programmed. The "Sleep" MODE program can be cancelled at any time during operation by again pressing the "Sleep" button. 8 SZ000302(En)-YaoKong(1018) 8 10/25/2004, 2:33 PM Air Conditioner Features (continued) CHECK FILTER FEATURE: YOU WILL SEE: LIGHT On Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. To reset after cleaning the filter, press the "Check Filter" button and the light will go off. CLEAN AIR FEATURE (on some models): YOU WILL SEE: LIGHT On DO THIS: PRESS CLEAN AIR BUTTON Note: When this feature is "ON", the electronic air purifier is energized to remove pollen and impurities from the air. To cancel this feature, press the Clean Air button (the LIGHT will turn off). [. . . ] Then, set Temperature to a Higher setting. Air conditioner cooling, but room is too warm - NO ice forming on cooling coil behind decorative front. Dirty air filter - air restricted. Allow additional time to remove "stored heat" from walls, ceiling, floor and furniture. Air conditioner turns on and off rapidly. Dirty air filter - air restricted. Set FAN speed to a faster setting to bring air past cooling coils more frequently. Noise when unit is cooling. Air movement sound. Refer to installation instructions or check with installer. Water dripping INSIDE when unit is cooling. [. . . ]