User manual AEG-ELECTROLUX LUX WIN100

[. . . ] To reduce the risk of electric shock, this product has a grounding type plug that has a third (grounding) pin. If the plug does not fit into the outlet, contact a qualified electrician to install the proper outlet. Never locate where it may fall into a bathtub or other water container. Do not insert or allow foreign objects to enter any openings as this may cause electric shock, fire, or damage to the thermostat. [. . . ] The abbreviation for the day of week will flash. WE COMPLETING YOUR INSTALLATION 7. Turn on your Air Conditioner or Space Heater and turn the thermostat all the way up. (This will allow the WIN100 to control the room temperature and maintain a specific temperature) 10. Verify that the Window Air Conditioner or Space Heater and its fan are operating properly. When set to a high temperature, the heating system should provide warm air after a short time. Likewise, a cooling system should provide cool air after a short time. The rush of moving air should be heard within a short time after either has been started. Pressing NEXT again will toggle from Set Time to Set Day, or vice versa. Return the dial to its RUN position. TEMPERATURE CONTROL MODES When a unit has first been powered up with the dial in the RUN position, your thermostat will begin to control your heating and/or air conditioning system according to it's default ENERGY STAR® approved program. There is a 2-position slide switch to change temperature control modes. Slide the switch to the mode you would like to use. HEAT Use HEAT mode to warm your home with a Space Heater. COOL Use COOL mode to control your Window Air Conditioner, cooling your home. Heating and cooling will be disabled, even though the set temperature, room temperature, and time will still be in the display. PROGRAMMING EDITING HEAT OR COOL PROGRAMS The WIN100 provides two separate programs, one for heating and the other for cooling. You can use the default programs or alter them to suit your schedule. ON/OFF SWITCH DEFAULT TEMPERATURE PROGRAM As supplied from the factory, the following ENERGY STAR® approved program will be used for temperature control in RUN MODE. This program and all other software settings may be restored to their default values via a SOFTWARE RESET. PERIOD HEAT MODE COOL MODE Morning 6:00 AM 70°F (21°C) 6:00 AM 78°F (26°C) 8:00 AM 62°F (17°C) 8:00 AM 85°F (30°C) Day Evening 6:00 PM 70°F (21°C) 6:00 PM 78°F (26°C) 10:00 PM 62°F (17°C) 10:00 PM 82°F (28°C) Night DEFAULT PROGRAM As supplied from the factory, your thermostat will use its default ENERGY STAR® approved program for temperature control. This program and all other settings may be restored to their default values via a SOFTWARE RESET. Please refer to DEFAULT TEMPERATURE PROGRAM for program times and temperatures. HOLD Hold is the simplest method to maintain fixed set temperatures. Press HOLD once to enter the temperature HOLD while in RUN or OVERRIDE. Pressing this button again will toggle HOLD off and return the unit to RUN and the programmed set temperature. Changing system mode or rotating the SPEED DIAL® will also cancel a HOLD. WEEKDAY PROGRAMMING To change the HEAT or COOL program: Set to HEAT if you are using a Space heater. Set to COOL if you are using a Window Air Conditioner Rotate dial to SET WEEKDAY PROGRAMS. MORN, Mo, Tu, We, Th, Fr will be displayed, with the Start Time flashing. [. . . ] However, they also serve as backup power to retain your programs and settings if you unplug it from the wall. The thermostat will alert you when the batteries are low by displaying "LO BATT" in the display. BATTERY INSTALLATION 1. Use a small regular screwdriver to remove the battery cartridge from the back of the thermostat. Use the small regular screwdriver to remove the 2 batteries from the holder. PROGRAMMING CHART The chart below is provided for you to write down your existing Weekday and Weekend program times and temperatures in case you have to enter them again at a later time. DAY MON. [. . . ]