User manual AEG-ELECTROLUX LUX T10-1143SA
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX LUX T10-1143SA. We hope that this AEG-ELECTROLUX LUX T10-1143SA user guide will be useful to you.
You may also download the following manuals related to this product:
AEG-ELECTROLUX LUX T10-1143SA (230 ko)
Manual abstract: user guide AEG-ELECTROLUX LUX T10-1143SA
Detailed instructions for use are in the User's Guide.
[. . . ] On new installations, the guidelines listed below should be followed as closely as possible. When replacing an old thermostat, install the new one in the same location unless these conditions suggest otherwise. Locate the thermostat on an inside wall about five feet above the floor, where it is easy to install and adjust. [. . . ] If adjustments are necessary, move heat anticipator pointer slightly and recheck. Turn electricity and gas back on and set pointer on top of thermostat to desired temperature. Thermostat will then cycle the blower "on" anf "off". If you find that it is uncomfortable some distance away from the thermostat, change the setting in order to compensate for this.
FIGURE 1 FRONT COVER FIGURE 2 BASE
MOUNTING HOLE
NOTE
2) TOOLS REQUIRED
Wirestripper or knife, drill with 3/16" bit, screwdriver, level and a pencil.
3) REMOVING OLD THERMOSTAT
Please read all instructions carefully. Disconnect wires from thermostat, making sure they do not fall back inside the wall. Make note of wires and to which terminals they are attached as you disconnect them. For example: "Yellow wire to terminal Y, Red wire to terminal RH, " etc. Strip insulation 3/8" from wire ends and clean off any corrosion. Fill wall opening with non-combustible insulation to prevent drafts from affecting thermostat. Place new decorative wall plate (if supplied), Figure 4, over wall opening. Remove Front Cover of new thermostat by inserting a finger in the side of the thermostat and gently prying away each corner. Remove Base, Figure 2, from SubBase, Figure 3, by loosening three captive screws. Insert plastic screw anchors into drilled holes, flush with wall surface. Bring wires through large hole in decorative wall plate and through Hole For Wires in Sub-Base. Referring to your notes and the following diagrams, attach wires to terminal screws shown in Figure 2. Push all excess wire back into wall.
UP
LON
GE
. 2
R
. 1 5
ANTICIPATOR
. 12
C YCLES
4) INSTALLING NEW THERMOSTAT
. 3
. 4
LONG POINTER CAPTIVE SCREW
CAPTIVE SCREW
. 5
HOLES FOR WIRES
. 25
MOUNTING HOLE
FIGURE 3 SUB-BASE
UP
horiz
vert
FIGURE 4 DECORATIVE WALL PLATE
UP
O
RH
G RC
A B Y W
WIRING DIAGRAMS
Heating Systems
FAN RELAY COOLING COMPRESSOR HEATING CONTROL HEATING TRANSFORMER DAMPER OR CHANGEOVER VALVE
(POWERED IN HEAT)
Cooling Systems
FAN RELAY COOLING COMPRESSOR HEATING CONTROL HEATING TRANSFORMER DAMPER OR CHANGEOVER VALVE
(POWERED IN HEAT)
TECHNICAL ASSISTANCE
(POWERED IN COOL)
DAMPER OR CHANGEOVER VALVE
(POWERED IN COOL)
DAMPER OR CHANGEOVER VALVE COOL TRANSFORMER
COOL TRANSFORMER
G
Y
W RH B
O
RC
G
Y
W RH B
O
RC
Tape Off
Tape Off **
4
H
5
V
Tape Off *
Tape Off
C
G
G
R*
B
*
Y
V
R
TC
C
RH
W
RC
F
RC
TC
If you have any problems installing or using this thermostat, please carefully and thoroughly review the instruction manual. [. . . ] Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. However, this product may replace a unit which NOTICE contains mercury and should not be disposed of in the trash. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX LUX T10-1143SA
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX LUX T10-1143SA will begin.