User manual AEG-ELECTROLUX HK764070FB

[. . . ] Do not put cutlery or saucepan lids on the cooking surface, as they can become hot. Overheated fats and oils can ignite very quickly. Correct operation Always monitor the appliance during operation. Do not put or keep very flammable liquids and materials, or fusible objects (made of plastic or aluminium) on or near the appliance. · Be careful when you connect the appliance to the near sockets. [. . . ] · Replace the damaged mains cable with a special cable (type H05BB-F Tmax 90°C; or higher). The appliance must have the electrical installation which lets you disconnect the appliance from the mains at all poles with a contact opening width of minimum 3 mm. You must have correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors. · · · · · · · Installation 5 Assembly min. 30 mm 6 Description of the appliance Description of the appliance Cooking surface layout 1 2 145 mm 265 mm 170 mm 120/175/210 mm 180 mm 1 2 3 4 5 6 3 Single cooking zone 1200 W Oval zone 1400/2200 W Control panel Single cooking zone 1800 W Triple cooking zone 800/1600/2300 W Control panel 6 5 4 Control panel layout 10 9 8 7 11 12 1 2 3 6 5 4 Use the sensor fields to operate the appliance. sensor field 1 2 3 4 5 6 7 function starts and stops the hob shows the heat setting activates automatic heat-up starts and stops the outer ring starts and stops the outer ring to set the heat setting increases or decreases the time a heat setting display with an indicator with an indicator a control bar / Operating the appliance sensor field 8 9 10 11 12 7 function selects the cooking zone shows the time in minutes shows for which zone you set the time starts and stops the key lock or child lock starts and stops STOP+GO the timer display cooking zones' indicators of timer a lock with an indicator with an indicator Heat setting displays Displays show which functions operate Display The cooking zone is off The cooking zone operates Keep Warm The automatic heat-up function is on + digit / / There is a malfunction OptiHeat Control (3 step Residual heat indicator): still cooking / keep warm / residual heat Lock/Child safety function is on The automatic switch off is on Description OptiHeat Control (3 step Residual heat indicator) WARNING!OptiHeat Control indicates the level of the residual heat. Operating the appliance On and Off Touch for 1 second to start or stop the appliance. Automatic Switch Off The function stops the hob automatically if: · all cooking zones are off . · you cover a sensor field with an object (a pan, a cloth, etc. ) for longer than 10 seconds. See the table. 8 Operating the appliance Automatic Switch Off times Heat setting Stops after 6 hours 5 hours 4 hours 1. 5 hours The heat setting Touch the control bar at the necessary heat setting. Do not release before you have a correct heat setting. / Switching the outer rings on and off You can match the effective heating surface to the size of the cookware. For To switch on the outer ring touch the sensor field / more outer rings touch the same sensor field again. The indicator goes out. The Automatic heat up The Automatic heat up function sets the highest heat setting for some time, and then decreases to the necessary level. To start function touch the symbol and than set the necessary heat setting. To stop the function change the heat setting. 12 11 10 9 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Using the Timer Count Down Timer Use the Count Down Timer to set how long the cooking zone operates for one cooking session. You can set the heat setting before or after you set the timer. Operating the appliance 9 · Selection of the cooking zone: touch again and again until the indicator of a necessary cooking zone comes on. · Starting the Count Down Timer: touch of the timer to set the time ( 00 - 99 minutes). When the indicator of the cooking zone flashes slower, the time counts down. · Changing the Count Down Timer: select the cooking zone with touch or . · Stopping the sound: touch CountUp Timer (Count up timer) Use the CountUp Timer to monitor how long the cooking zone operates. · Selection of the cooking zone (if more than 1 cooking zone operate): touch again and again until the indicator of a necessary cooking zone comes on. When the indicator of the cooking zone flashes slower, the time counts up, display switches between and time elapsed (minutes) · Checking the elapsed time: select the cooking zone with . · Stopping the CountUp Timer: select the cooking zone with and touch or to switch off the timer. Minute Minder You can use the timer as a Minute Minder while cooking zones do not operate. [. . . ] Switch on the signals. There is no signal when you touch panel keys Environment concerns 13 If you tried the above solutions and cannot repair the problem, speak to your dealer or the Customer Care Department. Give the data from the rating plate, three-digit-letter code for the glass ceramic (it is in the corner of the cooking surface) and an error message that comes on. If you operated the appliance incorrectly, the servicing by a customer service technician or dealer will not be free of charge, even during the warranty period. The instructions about the customer service and conditions of guarantee are in the guarantee booklet. Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste. [. . . ]