User manual AEG-ELECTROLUX HK654070XB

[. . . ] Children must get supervision to make sure that they do not play with the appliance. · Keep children away from the appliance when it is on. Installation instructions 3 WARNING!Start the child safety device to prevent small children and pets from an accidental activation of the appliance. Safety during operation · Remove all packaging, stickers and layers from the appliance before the first use. Do not put cutlery or saucepan lids on the cooking surface, as they can become hot. [. . . ] Use the correct mains cable of type H05BB-F Tmax 90°C (or higher) for a single-phase or two-phase connection. · Replace the damaged mains cable with a special cable (type H05BB-F Tmax 90°C; or higher). The appliance must have the electrical installation which lets you disconnect the appliance from the mains at all poles with a contact opening width of minimum 3 mm. You must have correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors. · · · · · · · Installation instructions 5 Assembly min. 30 mm If you use a protection box (additional accessory), the protective floor directly below the appliance is not necessary. 6 Product description PRODUCT DESCRIPTION Cooking surface layout 1 145 mm 2 170 mm 265 mm 5 1 75 20/1 /210 mm 145 mm 3 1 2 3 4 5 Single cooking zone 1200 W Oval zone 1500/2400 W Single cooking zone 1200 W Control panel Triple cooking zone 800/1600/2300 W 4 Control panel layout 1 2 3 4 5 6 7 8 12 11 10 9 Use the sensor fields to operate the appliance. sensor field 1 2 3 4 5 6 7 8 9 10 function starts and stops the hob starts and stops the key lock or child lock starts and stops STOP+GO activates automatic heat-up shows the time in minutes shows for which zone you set the time shows the heat setting starts and stops the oval zone to set the heat setting increases or decreases the time a lock with an indicator with an indicator the timer display cooking zones' indicators of timer a heat setting display with an indicator a control bar / Operating instructions sensor field 11 12 7 function selects the cooking zone starts and stops the outer rings with an indicator Heat setting displays Displays show which functions operate Display The cooking zone is off The cooking zone operates Keep Warm The automatic heat-up function is on + digit / / There is a malfunction OptiHeat Control (3 step Residual heat indicator): still cooking / keep warm / residual heat Lock/Child safety function is on The automatic switch off is on Description OptiHeat Control (3 step Residual heat indicator) WARNING!OptiHeat Control indicates the level of the residual heat. OPERATING INSTRUCTIONS On and Off Touch for 1 second to start or stop the appliance. Automatic Switch Off The function stops the hob automatically if: · all cooking zones are off . · you cover a sensor field with an object (a pan, a cloth, etc. ) for longer than 10 seconds. See the table. 8 Operating instructions Automatic Switch Off times Heat setting Stops after 6 hours 5 hours 4 hours 1. 5 hours The heat setting Touch the control bar at the necessary heat setting. The display shows the heat setting. A / Switching the outer rings on and off You can match the effective heating surface to the size of the cookware. For To switch on the outer ring touch the sensor field / more outer rings touch the same sensor field again. The indicator goes out. Automatic Heat Up 12 11 10 9 8 7 6 5 4 3 2 1 0 1 234567 8 9 10 11 12 13 14 You can get a necessary heat setting in a shorter time if you activate the Automatic Heat Up function. This function sets the highest heat setting for some time (see the graphic), and then decreases to the necessary heat setting. To stop the function change the heat setting. Operating instructions 9 Using the Timer Count Down Timer Use the Count Down Timer to set how long the cooking zone operates for one cooking session. · Selection of the cooking zone: touch again and again until the indicator of a necessary cooking zone comes on. · Starting the Count Down Timer: touch of the timer to set the time ( 00 - 99 minutes). When the indicator of the cooking zone flashes slower, the time counts down. · Changing the Count Down Timer: select the cooking zone with touch or . · Stopping the sound: touch CountUp Timer (Count up timer) Use the CountUp Timer to monitor how long the cooking zone operates. · Selection of the cooking zone (if more than 1 cooking zone operate): touch again and again until the indicator of a necessary cooking zone comes on. When the indicator of the cooking zone flashes slower, the time counts up, display switches between and time elapsed (minutes) · Checking the elapsed time: select the cooking zone with . · Stopping the CountUp Timer: select the cooking zone with and touch or to switch off the timer. [. . . ] Switch on the signals. There is no signal when you touch panel keys If you tried the above solutions and cannot repair the problem, speak to your dealer or the Customer Care Department. Give the data from the rating plate, three-digit-letter code for the glass ceramic (it is in the corner of the cooking surface) and an error message that comes on. If you operated the appliance incorrectly, the servicing by a customer service technician or dealer will not be free of charge, even during the warranty period. The instructions about the customer service and conditions of guarantee are in the guarantee booklet. ENVIRONMENT CONCERNS The symbol on the product or on its packaging indicates that this product may not be treated as household waste. [. . . ]