User manual AEG-ELECTROLUX HK634060XB

[. . . ] Children must get supervision to make sure that they do not play with the appliance. Start the child safety device to prevent small children and pets from an accidental activation of the appliance. Installation 3 Safety during operation · Remove all packaging, stickers and layers from the appliance before the first use. Do not put cutlery or saucepan lids on the cooking surface, as they can become hot. Overheated fats and oils can ignite very quickly. Correct operation · · · · Always monitor the appliance during operation. [. . . ] A qualified electrician must install the clamping connections correctly. Use the correct mains cable of type H05BB-F Tmax 90°C (or higher) for a single-phase or two-phase connection. · Replace the damaged mains cable with a special cable (type H05BB-F Tmax 90°C; or higher). The appliance must have the electrical installation which lets you disconnect the appliance from the mains at all poles with a contact opening width of minimum 3 mm. You must have correct isolation devices: line protecting cut-outs, fuses (screw type fuses removed from the holder), earth leakage trips and contactors. · · · · · · · Installation 5 Assembly 600 mm min. 30 mm 6 Description of the appliance Description of the appliance Cooking surface layout 1 2 145 mm 265 mm 170 mm 120/210 mm 145 mm 3 1 2 3 4 5 Single cooking zone 1200 W Oval cooking zone 1500/2400 W Single cooking zone 1200 W Control panel Double cooking zone 750/2200 W 5 4 Control panel layout 1 2 3 4 5 6 7 11 10 9 8 Use the sensor fields to operate the appliance. sensor field 1 2 3 4 5 6 7 8 9 10 function starts and stops the hob locks/unlocks the control panel shows the heat setting shows for which zone you set the time shows the time in minutes increase or decrease heat setting starts and stops the outer ring increase or decrease the time selects the cooking zone starts and stops the outer ring with an indicator a heat setting display cooking zones' indicators of timer the timer display / with an indicator / Operating the appliance sensor field 11 7 function starts and stops the STOP+GO function Heat setting displays Displays and sounds tell which functions operate Display The cooking zone is off The cooking zone operates Keep Warm / function is on Description The automatic heat-up function is on There is a malfunction A cooking zone is still hot (residual heat) Lock/Child safety function is on The automatic switch off is on Residual heat indicator WARNING!Risk of burns from residual heat! Operating the appliance On and Off Touch for 2 seconds to start the appliance. Touch for 1 second to stop the appliance. Automatic Switch Off The function stops the hob automatically and comes on if: · all cooking zones are off . · you cover a sensor field with an object (a pan, a cloth, etc. ) for longer than 10 seconds. · you do not stop a cooking zone or change the heat setting after some time. Automatic Switch Off times Heat setting Stops after 6 hours 5 hours 4 hours 1. 5 hours 8 Operating the appliance The heat setting Touch to increase the heat setting. Touch and at the same time to switch off the cooking zone. / Switching the outer rings on and off You can match the effective heating surface to the size of the cookware. For To switch on the outer ring touch the sensor field / more outer rings touch the same sensor field again. The indicator goes out. The automatic heat up function The automatic heat up function starts when you set a heat setting starting from . A cooking zone operates with the maximum power for some time and than automatically switches back to the heat setting you set. If you set a higher heat setting during the automatic heat up (for example from to ), the automatic heat up is adjusted. If there is still residual heat on the cooking zone (display ), the automatic warm up does not start. The time of the automatic warm up changes for different heat settings: 11 10 9 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 9 Starting the STOP+GO The function sets all cooking zones that operate to a keep warm setting. fully locks the control panel but not the sensor field . Using the Timer Use the timer to set how long the cooking zone operates for one cooking session. · Selection of the cooking zone: touch again and again until the indicator of a necessary cooking zone comes on. · Starting the timer: touch or of the timer to set the time ( 00 - 99 minutes). [. . . ] If comes on again, speak to the after sales service. and a number come on. If you tried the above solutions and cannot repair the problem, speak to your dealer or the Customer Care Department. Give the data from the rating plate, three-digit-letter code for the glass ceramic (it is in the corner of the cooking surface) and an error message that comes on. If you operated the appliance incorrectly, the servicing by a customer service technician or dealer will not be free of charge, even during the warranty period. The instructions about the customer service and conditions of guarantee are in the guarantee booklet. 12 Environment concerns Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste. [. . . ]