User manual AEG-ELECTROLUX GLD2250RDC

[. . . ] (If the drain hose is installed through the floor, an air gap is necessary). The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. Drain Hose Cut for 3/4" connection. Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. 90° 341/4" min. 90° Property Damage Electrical, water, and drain lines must be confined to shaded area. · Examine dishwasher and locate connections. [. . . ] Tighten elbow with a wrench, leaving elbow pointing toward rear of unit. To prevent bending of bracket or breaking of valve, avoid overtightening. 16 3/8" From rear to center of water inlet valve. Junction Box (not visible) L Figure 7(a) 6" Sink at Left Drain Air Gap Through Cabinet Alternate Drain Through Floor into Separate Trap Remove Knockout Plug in Disposer Figure 7(b) Figure 4 Sink at Right 2" Drain Hose Hole 4. IMPORTANT: Incoming hot water temperature should be at least 120°F (49°C). Before cutting drain hose access, check both sides of selected area to avoid interference. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. Drain 1. Review Figures 5 and 6 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. 4 Figure 5 Entry Must be Above Trap "Y" Branch Tailpiece Right Side 49 1/4" 22 1/2" Sink at Left Sink at Right 2" Drain Hose Hole Door in open position Floor Line 2. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 5. 17 3/4" From rear to junction box. Leveling Dishwasher within Cabinets 1. Measure height of cabinet opening from underside of countertop to floor. Check chart for height opening and suggested adjustment. 5 Sink at Left Connector 32" Clamp Electrical Supply 1. Use a UL listed conduit connector, not included, at box to stabilize wiring. IMPORTANT: Be sure electrical cable is not routed behind dishwasher's motor. Floor Anchoring This procedure is difficult and should be used only if countertop mounting brackets cannot be used. Screw 1/4" lag screws, not included, through holes provided in frame rail. Place door where it will not get scratched or damaged while completing installation. When ready to replace door, fit the slots on each side of top door edge over the tabs on the metal liner. See Figure 16c. Figure 16c Use 1/4" Lag Screws (not included) Console Metal Liner Door Pump Motor Leg Leveler Adjustment Chart Height of Number of Turns to Cabinet Opening Adjust Levelers 34" (86. 4cm) 0 341/8" (86. 7cm) 345/16" (87. 2cm) 34 /2" (87. 6cm) 1 Remove knockout plug in disposer Figure 10 Through Wall 2 6 9 The drain hose loop must be at least 32" high from the floor to insure proper drainage. Through Cabinet Figure 15 For additional height add shims under levelers. Front levelers should allow 1/4" below underside of countertop. Finishing the Water Connection 7 Through Floor Junction Box (in place) Note: If mounting your dishwasher to the countertop or to the floor is not a desirable option, you can order the side mount kit, 154477201, by contacting your dealer or parts supplier. This allows you to install the dishwasher by securing it to the cabinets or partitions on either side of the unit. The kit utilizes the front frame of the dishwasher to secure the unit to the cabinet or partitions. Side View Appearance of console and door may vary from your model. 6. [. . . ] The equipment-grounding conductor must be run with the circuit conductors and connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. Do not connect the dishwasher to the power supply until the appliance is permanently grounded. Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes. [. . . ]