User manual AEG-ELECTROLUX ESI682-X

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX ESI682-X. We hope that this AEG-ELECTROLUX ESI682-X user guide will be useful to you.


AEG-ELECTROLUX ESI682-X : Download the complete user guide (584 Ko)

Manual abstract: user guide AEG-ELECTROLUX ESI682-X

Detailed instructions for use are in the User's Guide.

[. . . ] . 3 Operating Instructions 1 Safety Prior to using for the first time · Follow the "Instructions for installation and connection". Correct use · The dishwasher is only intended for washing domestic dishes. · Additions or modifications to the dishwasher are not permitted. · Use only special salt, detergent and rinse aid suitable for domestic dishwashers. This could cause an explosion. Child safety · Keep packaging away from children. [. . . ] Before the start of the dishwashing cycle put 3in1 detergent in the detergent dispenser. 3 As the off when theinflow function is activatrinse aid is automatically switched 3in1 ed, it may come about because of the different quality standards in the 3in1 detergent, that the dishes do not dry sufficiently. If this happens, proceed as follows (see section "Adding rinse aid"): · Fill up the dispenser (if this is empty) with rinse aid. · Activate rinse aid inflow. If you do not want to use 3in1 products any more If you want to stop using 3in1 products, please do the following: · Deactivate the 3in1 function. · Switch the water softener to the highest setting and perform up to three normal cycles without loading any dishes. · Then set the water softener to the water hardness in your area. If you want to use 4in1 products When using "4 in 1" detergents that integrate also anti- glass corrosion agent into "3 in 1" formula, please follow the same indication as given for "3 in 1" detergents. 19 Selecting the dishwashing cycle (Cycle Table) Programme sequence Intermediate rinse Dishwashingcycle Suitable for: Type of soiling Pre-wash Consumption values1) Length (minutes) Energy (kWh) 1, 80 - 2, 00 0, 8 0, 95 - 1, 05 0, 9 2x 2) Dinner service and cookware Dishes, excluding saucepans heavily soiled, dried-on food remains, in particular protein and starch just used, lightly to normally soiled 120 - 130 · · · · - · - · - 30 4) Dinner service and cookware, temperanormally soiled ture-sensitive crockery Dessert dishes and coffee service, delicate glassware lightly soiled 130 - 160 · · · · · 73 - · · · 1) The consumption values were obtained under standardised conditions. 2) During the final rinse, the temperature is increased to 68° for 10 minutes to sanitize e. g. 4) Test programme for Test Institutes 20 14 2x 14 - 16 9 3) 22 - 24 Water (litres) Main wash Final rinse Drying Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e. g. The remaining time expected for the cycle will be shown in the multi-display. The selected cycle will begin after approximately 3 seconds. Setting the Delay Timer a dishwashing cycle for between 1 and 19 hours. 1. Press the Delay Timer button repeatedly until the multi-display shows the desired time delay, for example 12h, if the cycle is to start in 12 hours. 3. The time remaining to the start of the cycle is continuously displayed (e. With other fault codes ("Å " followed by a number): ­ Abort the dishwashing cycle. If the fault is displayed again, please contact the Customer Care Department and inform them of the fault code. Malfunction Possible cause Remedy Water tap is blocked with limescale Check the water tap and have it reor faulty. The filter (where present) in the threaded hose fitting on the tap is blocked. Cancel the dishwashing cycle (see chapter: Starting a dishwashing cycle), clean filters (see chapter: Cleaning the filters), then start the dishwashing cycle again. First shut off the water tap, then switch off the appliance and contact the Customer Care Department. Plug in mains plug. The cycle indicator for the selected dishwashing cycle is flashing: fault code Å 10 is displayed in the multi-display: Filters in the base of the dishwash(Problems with water inlet) er compartment are blocked. Water inlet hose has not been correctly positioned. ed dishwashing cycle is flashing, fault code Å 20 is displayed in the Water drain hose multi-display. (Problems with water drainage) Fault code Å 30 is displayed in the The anti-flood system has been multi-display. The cycle is not starting. A fuse in the house's wiring system Replace fuse. For dishwasher models with a delay If the dishes are to be washed imstart timer: mediately, cancel the delay start. [. . . ] The inlet hose is fitted with either a plastic or a metal nut: ­ Only tighten the nut hand tight. (Make sure that the tap is not dripping. ) 1 The water inlet hose must not be kinked, 3 So that accessthe use tap thethe kitchen is not to the in restricted by of dishwasher, we recommend installing an additional tap, or fitting a T-branch to the existing tap. If you need a longer water inlet hose than that supplied, the following VDE-approved complete hose sets are to be used. ­ Hose kit "WRflex 100" (Code: 911 239 034) ­ Hose kit "WRflex 200" (Code: 911 239 035) 34 Water drainage Drain hose 1 The drain hose must not be kinked, crushed or entangled. · Connecting the drain hose: maximum permitted height above the bottom edge of the appliance: 60 cm. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX ESI682-X




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX ESI682-X will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.