User manual AEG-ELECTROLUX E30EW85PSS INSTALL

[. . . ] Electrical Junction Box ** Door Open (see note) A D 111/2"* (29. 2 cm) 2" (5. 1 cm) Min. Figure 1 PRODUCT DIMENSIONS MODEL 30" (76. 2 cm) Wall Oven A 30 (76. 2) B 521/8 (132. 4) C (Rear wrapper) 281/4 (71. 8) D 241/2 (62. 2) CUTOUT DIMENSIONS AND CABINET WIDTH MODEL 30" (76. 2 cm) Wall Oven Min. 28½ (72. 4) F Max. 29 (73. 7) G (Min. ) 24 (61) Min. H Max. I 30 (76. 2) Min 51 (129. 5) 513/4 (131. 4) All dimensions are in inches (cm). Printed in United States P/N 318201520 (0411) Rev. A English ­ pages 1-6 Español ­ páginas 7-13 Français ­ pages 14-20 1 ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS Important Notes to the Installer 1. Read all instructions contained in these installation instructions before installing the wall oven. Remove all packing material from the oven compartments before connecting the electrical supply to the wall oven. [. . . ] · Disconnect power to the junction box before making the electrical connection. · This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance. Failure to do any of the above could result in a fire, personal injury or electrical shock. During cold temperature weather to prevent damage to the oven control, wait at least three (3) hours after receiving this built-in oven before switching the power. This will prevent possible damage to the built-in oven control at power on. 1. Carpentry Refer to figure 1 for the dimensions applicable to your appliance, and the space necessary to receive the oven. The oven support surface may be solid plywood or similar material, however the surface must be level from side to side and from front to rear. 2. Electrical Requirements This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse, having amperage as noted on the rating plate (the rating plate is located on the oven frame). Observe all governing codes and local ordinances 2 ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS 3. Electrical connection It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the National Electrical Code ANSI/NFPA No. 70-latest edition, or with CSA Standard C22. 1, Canadian Electrical Code, Part 1, and local codes and ordinances. If connection is made to aluminum house wiring, use only special connectors which are approved for joining copper and aluminum wires in accordance with National Electrical Code and local codes and ordinances. These appliances are manufactured with a white neutral power supply wire and a frame connected green or bare copper grounding wire. If local codes permit connection of the frame grounding conductor to the neutral (white) wire. Connect the green (or bare copper) wire and the white wire from the appliance cable to the supply cable ground wire (white or bare) inside the junction box. Connect the remaining wires inside the junction box from the power supply cable to the matching colors of the appliance cable wires (figure 2). Cable from Power Supply Ground Wire Red Wires Black Wires 2. If used in mobile homes or if local codes DO NOT permit connection of the frame grounding conductor to the neutral (white) wire, separate the white and bare copper ground wires that extend out of the end of the supply cable of the appliance. Connect the white wire from supply cable to the neutral white wire in the junction box. Connect the black and red wires from the supply cable to the matching color wires in the junction box. The bare wire must now be used to ground the appliance in accordance with local electrical codes. Connect the bare copper ground wire to the grounded lead in the service panel. DO NOT connect to electrical power supply until appliance is permanently grounded. [. . . ] The mounting brackets supplied with the wall oven must be attached to the cabinet and the appliance to prevent tipping of the wall oven and injury to persons. Mounting Brackets Installation Instructions 1. Unpack the wall oven and find the 2 mounting brackets and screws included in the literature package. Note: To prevent damage to cabinet, it is recommended to drill 1/16" (0. 16 cm) dia. pilot holes before installing the mounting brackets. Cutout Dimensions 28 1/2" (72. 4 cm) Min. * 29" (73. 7 cm) Max. * 1 1/2" (3. 8 cm) clearance between unit and front of cabinet Figure 5 * Recommended Cutout Width is 28½" (72. 4 cm) Mounting Brackets 46" (117. 2 cm) 51" (129. 5 cm) Min. [. . . ]