User manual AEG-ELECTROLUX DL8560-M

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX DL8560-M. We hope that this AEG-ELECTROLUX DL8560-M user guide will be useful to you.


AEG-ELECTROLUX DL8560-M : Download the complete user guide (2254 Ko)

You may also download the following manuals related to this product:

   AEG-ELECTROLUX DL8560-M (7021 ko)
   AEG-ELECTROLUX DL8560-M (7021 ko)
   AEG-ELECTROLUX DL8560-M (7021 ko)
   AEG-ELECTROLUX DL8560-M (7021 ko)
   AEG-ELECTROLUX DL8560-M (7021 ko)
   AEG-ELECTROLUX DL8560-M (7021 ko)

Manual abstract: user guide AEG-ELECTROLUX DL8560-M

Detailed instructions for use are in the User's Guide.

[. . . ] Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood. If the extractor is used in conjunction with non-electrical appliances (e. Gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. [. . . ] By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Ty 1 Product Components Hood Body, complete with: Controls, Light, Blower, Filters Directional Air Outlet grille Flange ø 150 mm Flange with Valve ø 150 Installation Components Hood body fixing brackets Screws 3. Remove the profile after unfastening the 4 screws that fix it to the Hood (fig. By removing the 6 upper screws, the 6 rear screws and the 2 screws on the inside of the Hood, it is possible to turn the Motor Unit with the bracket attached so that the air outlet points to the side (fig. 4) unfasten from the inside the screws that fix the upper part containing the motor to the rest of the Hood. Turn the upper part as required, to the right or left, and then refasten the screws removed as above from the inside (fig. From the Cooker Top) using the snap-on side supports and screws provided. Create an opening in the bottom of the wall mounted unit, as shown (fig. The brackets must be fitted differently according to the size of the hood to be mounted. Remove the profile after unfastening the 4 screws that fix it to the Hood (fig. It is now possible to fasten the hood to the wallmounted unit using the screws 12a (3. When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120mm, the choice of which is left to the installer. Cut a hole ø 125 mm in any shelf that may be posi-tioned over the hood. Fix the directional grille 8 on the recirculation air outlet using the 2 screws 12e (2, 9 x 12, 7) provided. Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button. The function becomes active when the button is pushed for about 2 seconds. [. . . ] The alarm signal will only light up when the extractor motor is switched on. Disconnect the Hood using the Main switch or the double-pole switch on the mains power supply. Within 3 seconds press T1 until LEDs T1 and T4 flash in confirmation: LED flashes twice - Activated charcoal filter saturation alarm ENABLED. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX DL8560-M




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX DL8560-M will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.