User manual AEG-ELECTROLUX DI7490-M

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual AEG-ELECTROLUX DI7490-M. We hope that this AEG-ELECTROLUX DI7490-M user guide will be useful to you.


AEG-ELECTROLUX DI7490-M : Download the complete user guide (5934 Ko)

You may also download the following manuals related to this product:

   AEG-ELECTROLUX DI7490-M (5953 ko)
   AEG-ELECTROLUX DI7490-M (5953 ko)
   AEG-ELECTROLUX DI7490-M (5953 ko)
   AEG-ELECTROLUX DI7490-M (5953 ko)
   AEG-ELECTROLUX DI7490-M (5188 ko)
   AEG-ELECTROLUX DI7490-M (5953 ko)
   AEG-ELECTROLUX DI7490-M (5953 ko)

Manual abstract: user guide AEG-ELECTROLUX DI7490-M

Detailed instructions for use are in the User's Guide.

[. . . ] The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells. Never use the hood for purposes other than for which it has ben designed. Never leave high naked flames under the hood when it is in operation. [. . . ] Tighten the two screws and fasten the other two screws provi-ded with the hood. Before tightening the screws completely it is possible to adjust the frame by turning it. Make sure that the screws do not come out of their seats in the slotted holes. The frame mountings must be secure to withstand the weight of the hood and any stresses caused by the occasional side thrust applied to the device. In all cases where the ceiling is not strong enough at the suspension point, the installer must provide strengthening using suitable plates and backing pieces anchored to the structurally sound parts. INSTALLATION CONNECTION IN DUCTING VERSION When installing the ducting version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. 1 is in correspondence with the Chimney openings both horizontally and vertically. Join the Connector 15 to the Hood canopy outlet using a rigid or flexible pipe ø¸150 mm, selection of which is at the discretion of the installation technician. Position the upper chimney section and fix the upper part to the frame using the 2 screws 12c (2, 9 x 6, 5) provided. Similarly, position the lower chimney section and fix the lower part to the frame using the 2 screws 12c (2, 9 x 6, 5) provided. Before fixing the hood body to the frame: · Screw the 2 screws 12f half way into the holes provided in the sides of the bottom of the frame. Working from below, fix the hood canopy to the frame (B), using the 4 screws 12q and 4 washers 22 provided, then tighten all the screws securely. Connect the hood to the mains through a twopole switch ha-ving a contact gap of at least 3 mm. Place the connectors in the junction box 24 and close it using the 2 screws 12e (2, 9 x 9, 5) provided. Fix the junction box to the hood body using the 2 screws 12c (2, 9 x 6, 5) provided. DISPLAY Displays the set speed Displays the set speed Displays the set speed Displays HI The spot flashes FUNCTIONS Turns the suction motor on and off Decreases the speed of the motor V3 V2 V1 Increases the speed of the motor V1 V2 V3 Starts maximum suction speed. [. . . ] Before fitting them again into the hood make sure that they are completely dry. (The colour of the filter surface may change through-out the time but this has no influence to the filter efficiency). When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing outwards. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AEG-ELECTROLUX DI7490-M




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual AEG-ELECTROLUX DI7490-M will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.