User manual AEG-ELECTROLUX DD9894-M

[. . . ] 10 Cleaning the hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Special accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Technical assistance service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Technical Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Top Rear Ø 150 mm Top Rear Ø 120 mm Coupling ring Fig. 1 Recirculation mode · The air is filtered through a charcoal filter and returned to the kitchen. 2 · You will need an original charcoal filter for the recirculation mode. 2 5 Control Panel · Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. The control switches are located on the unit's front panel: ab 1 2 3 4 5 6 6 1 - Mains switch, ON/OFF Press for less than 1 1/2 seconds and the cooker hood goes into the "stand by" position (point "b" is illuminated). Press for more than 1 1/2 seconds and the cooker hood turns off, ALL the controls (except the light push button) are disabled (the display is off). Press again for more than 1 1/2 seconds to reset the cooker hood to "stand by". 2 - Light ON/OFF 3 - Display 4 - Start and choice of motor speed 1-2-3-1-2. . . . . . . . . The Intensive speed runs for 5 minutes: If the hood is on when the Intensive speed is activated, the hood will revert to previous speed after 5 minutes. If the hood is off when the Intensive speed is activated, the hood will automatically turn off after 5 minutes. The letter P appears on the display and the remaining time (the point "a" is flashing), if interrupted an acoustic signal is heard. 6 - Self-Timer: times all the speed levels (the point "b" is flashing), and then the cooker hood switches off: The self-timer is set as follows: 1st speed level 20 minutes 2nd speed level 15 minutes 3rd speed level 10 minutes The display shows the remaining operation time, at the end of the time an acoustic signal is heard. Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds. After reconnecting the power supply wait 15 seconds and then check that the cooker hood is now operating correctly. Grease and charcoal filter maintenance indicator This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter). On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled. If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows: Press buttons 4 and 5 simultaneously and hold them for 3 seconds. At first only the grease filter LED F will light up, but when the charcoal filter LED C lights up the saturation indicator will be enabled. To disable it: Press buttons 4 and 5 again simultaneously and hold them for 3 seconds, until the charcoal filter LED C goes out. Grease filter LED (F) LED F will start to flash when it is time to clean the grease filter. Always comply with the maintenance instructions for the grease filter. Charcoal filter LED (C) The charcoal filter LED C will start to flash when the charcoal filter needs to be replaced. [. . . ] · Mark the wall with a centre line, this will aid mounting procedure (1), position the template so that the mid line printed on the template matches with the centre line previously drawn, the lower side of the template corresponds to the lower side of the hood once mounted (2). · Make holes as indicated on the template, insert the wall dowels and fix the support bracket with two screws into the upper holes (3). The upper 2 are for hooking the hood up while the lower hole is for the definitive and safety fixing. · Drill two holes Ø 8mm on the upper side close to the ceilling, fit two wall plugs (4) and fix the chimney support G with two screws (5). [. . . ]