User manual AEG-ELECTROLUX AEG W1250

[. . . ] LAVAMAT W 1250 ELECTRONIC Washing Machine User information Dear Customer, Please read this user information carefully. Pay particular attention to the section "Safety" on the first Info pages. Please keep this user information in a safe place for later reference. Pass it on to any future owners of the unit. 1 The warning triangle and /or signal words (Warning!, Caution!, Important!) emphasise information which is important for your safety or for the unit's functional reliability. [. . . ] Check that you are able to turn the pump wheel at the very rear of the pump housing. (If the wheel rotates with a jerky motion, this is normal. ) If you cannot turn the pump wheel, contact customer service. 6. Insert the webs on the cover laterally into the guide slots and screw on the cover securely clockwise. 7. 28 Operating Instructions What to do if . . . Remedying Faults In the event of a fault, try to solve the problem yourself with the aid of the information provided here. If you call Customer Service to deal with one of the faults listed here or to remedy an operating fault, the customer service technician's visit will not be free of charge, even during the warranty period. Problem Possible cause Remedy The mains plug is not inserted. There should be an audible click. Press and hold the START/ The START/PAUSE button was PAUSE button until the pronot pressed for long enough. Release child safety feature The door cannot be The child safety feature is en(see Section "Child Safety Feaclosed. Disconnect the hose from the water tap, remove the filter and clean under running water. First turn the programme selector to OFF, then set the desired programme to the exact position. The END indicator flashes once. The filter in the socket of the inlet hose is blocked. Water tap is blocked with limescale or is faulty. The programme selector has not clicked into place correctly. 29 Operating Instructions Problem Possible cause Remedy Remove the transit packaging Transit packaging was not reas described in the Installation moved. The washing machine vibrates when There is very little washing in the drum (for example one operating, or is dressing gown). Water could not be fully drained out before spinning because the drain hose is kinked or the water pump is blocked. Adjust the feet according to the Installation and Connection instructions. Check the drain hose and remove any kinks if necessary or clean the water pump and if necessary remove any foreign bodies from the pump housing. Close the cover correctly. Probably too much detergent has been used The screw connection of the inlet hose is leaking. The drain pump cover is not correctly closed. Water leaks out Stop the programme, remove of the washing maWashing is caught in the door. Close the emergency emptying hose (see Section "Carry The emergency emptying hose out emergency emptying"). Fabric softener was The insert in the conditioner not rinsed in, the compartment is not correctly æ compartment is attached or is blocked. Clean the detergent dispenser drawer and attach the conditioner insert correctly. 30 Operating Instructions Problem Possible cause Remedy Pay attention to the maximum load quantity (see Programme Tables). Always load the drum as ful as possible with a combination of large and small items. For pumping heights over 1 m a conversion kit is available as a special accessory. Wait until the programme has ended, the DOOR light goes off and the END light is lit. [. . . ] Terlaton Street 42/44 1011 Riga Tel. : 371 2 297821 Fax: 371 2 821286 Lthuania Electrolux Lthuania Verkui 29 2600 Vilnus Tel. : 372 272 3326 Fax: 372 272 3366 Poland Electrolux Poland Sp. Domaniewska 41 02-034 Warszawa tel. : 022 874 33 33 fax: 022 874 33 00 Russia Electrolux Russia Ltd. 16 Olympiysky prospekt 129090 Moscow Tel. : (095) 937 7837 Fax: (095) 926 5513 47 Warranty conditions / Customer service centres Israel Electricity & Electronic Services-Evis LTD. Raanana, Industrial area 43654 Tel: 972-9-7448118 Fax: 972-9-7603618 e-mail:evis@evis. co. il Malaysia Arzbergh Engineering No. [. . . ]