User manual ACER TRAVELMATE 4350

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the device into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/television technician for help. [. . . ] Upon request, you must provide this information to your telephone company. If your telephone equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. But, if advance notice is not practical, you will be notified as soon as possible. You will also be informed of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service. If this equipment should fail to operate properly, disconnect the equipment from the phone line to determine if it is causing the problem. If the problem is with the equipment, discontinue use and contact your dealer or vendor. TBR 21 This equipment has been approved [Council Decision 98/482/EC - "TBR 21"] for single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries, the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN termination point. In the event of problems, you should contact your equipment supplier in the first instance. For more information about applicable countries, please refer to "Regulations and safety notices" on page 46 English This device complies with Part 15 of the FCC Rules. Specifications ACER T1125 Notebook 2 x USB 2. 0 2 x USB 3. 0 HDMI, D-sub, ODD SATA RJ45 Mic-in, Earphone-out DC-in Jack 10/100/1000Base-T Compliant Ethernet LAN Slot-in DVD-Super Multi Dual-Layer Drive Power On / Off Button Battery Capacity inspection Button 96. 7(W) x 301. 3(D) x 56. 9(H)mm about 465g (without external Optical Disk Driver) Compatibility Description The docking port is used to interface between the notebook and the station itself allowing control and connectivity. The docking port is used to interface between the External ODD and the station itself. The Power On / Off button can switch on and shut down the attached notebook. To inspect the battery capacity of the attached notebook LAN External Optical Disk Driver Buttons Dimensions Weight 2 3 4 * The Specifications list above may appear different from your model. D1125 SERIES USER'S MANUAL 1. 3 Rear View: Docking Station The below image shows the rear of the docking station. All of the interface ports for peripherals are on the rear of the docking station. Please refer to the below image to see placement of the ports. 1 2 5 USB2. 0 Ports The Docking Station has a total of 2 available USB2. 0 Ports for peripheral connections and the ports are USB 2 Compliant. The Docking Station has a total of 2 available USB3. 0 Ports for peripheral connections and the ports are USB 3/ USB 2 Compliant. For Connecting High Definition Monitors and TVs/Panels. English 6 7 4 USB3. 0 Ports HDMI Port HDMI 3 LINE OUT 9 7 6 5 # 1 Item RJ-45 LAN Port Description The LAN Port is used to connect the Docking Station and docked notebook to a wired network. The VGA D-Sub port is used to connect an external analogue monitor to the docking station. For connecting External Speakers/ Headphones. 2 3 4 VGA D-Sub Port Mic-In Jack Audio Jacks 1. 4 Side Views: Docking Station The below image shows the Left t side of the ACER Docking station. Please refer to the below images for reference to ports / connectors. 1. 5 Dock and Un-dock of the Docking Station 1 Connect the AC adaptor and power cord Connect the AC adaptor to ensure that the Docking Station is powered. [. . . ] When the notebook is placed the right way up, the docking connectors will be on the same side. Ensure that these are aligned correctly before trying to dock the notebook to the docking station. Rotate the Docking Station T1125 can be used as the second Screen output if rotate the D1125 anti-clockwise up to 90 degree with the T1125 in Tablet PC mode. English OPE N 11 1. 6 Line up the notebook with the docking station as shown above and make sure of the positioning. Use the operating systems display properties to then get an image on the HDMI Output port. 1. 10 How To: Connect an RJ45 Ethernet LAN The docking station features an RJ45 Ethernet port with an integrated LAN controller capable of operational speeds of 10Mbps, 100Mbps or 1 Gigabit (1000Mbps) ­ When active it will override the port on connected notebooks. English 13 HDMI HDMI LINE OUT LINE OUT Disconnect an HDMI Display To remove the cable simply grab the head of the cable and gently pull out of the GRFN, ensuring that the port is no longer active with a display output. DO NOT pull by the cable itself is this can damage the HDMI cable or the cables connector head as well as the HDMI port. English 14 Chapter 2 External ODD This section will tell you how to connect and operate the External ODD that comes with D1125. [. . . ]