User manual ACER S1213HN

[. . . ] The projector automatically shuts off when the lamp is used up in about 2, 000 hours and cannot be used until lamp replacement. DO NOT LOOK DIRECTLY INTO THE LENS WHEN PROJECTOR IS IN THE POWER ON MODE. When using the projector in Europe COMPLIANCE NOTICE This LCD - Video Projector complies with the requirements of the EC Directive 89/336/EEC "EMC Directive" as amended by Directive 93/68/EEC and 73/23/EEC "Low Voltage Directive" as amended by Directive 93/68/EEC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. [. . . ] · When input signal is jittering, please adjust by $ or % button also connecting with DVD player or MUSE decoder etc. · When supplying unstable signal like Still or Reverse play with VCR, "NO SIGNAL" may appear on the screen. In this case, you may avoid this issue by selecting the right color format like NTSC, PAL in OPTION menu. Adjust the focus with the focus ring by turning it. focus ring tele Stand-by When light source lamp is on Light source lamp held off temporarily Green - Red Green Red Important: · A darkened image may be seen right after pressing the POWER button due to warming up of this projector. While warming up, no other commands can be accepted. zoom ring wide near far ´ EN ­ 13 To operate projector power ON (Continue) Turning off the projector 7. · To exit from this mode, press any button except POWER, LASER, mouse pointer, R/L-click, STILL and VOLUME + and - buttons. Pressing the POWER button second time will shut off the light source lamp, but the exhaust fan continues to operate for 120 seconds to cool down the light source lamp and LCD panels. · In cases where the main power switch is accidentally turned off when either the intake/exhaust fan or the power source lamp is in operation, allow the unit to cool down for 10 minutes with the power turned off. If the lamp does not turn on immediately, repeat this step two or three times. AUTO POSITION button When the source is selected to COMPUTER and the image is not in the right place, set the screen to the brightest display possible, then press the AUTO POSITION button on the remote control. · Set screen to the brightest display as possible (e. g. , full-screen display of the "Trash" window) before deploying the automatic adjustment function. Press the $ or % button to select the INSTALLATION menu. Opt XGA60 6. · If the menu operation is not working, press the RESET button on the terminal board using the suitable implement · If the COMPUTER or VIDEO button is pressed, the MENU selection bar or MENU will disappear. · The settings with 2 mark, you should press the ENTER button after selecting. INSTALLATION 3. Press the ENTER button (or } button). Opt XGA60 OFF 0° OFF OFF INSTALLATION IMAGE REVERSE KEYSTONE AUTO POWER ON AUTO POWER OFF EN ­ 15 ENGLISH CONTRAST BRIGHTNESS COLOR MATRIX ± 30 ± 30 1 2 3 USER OFF STANDARD HIGH LOW USER ± 10 ± 10 ± 10 RED GREEN BLUE YELLOW CYAN MAGENTA ± 10 ± 10 ± 10 ± 10 ± 10 ± 10 Menu operation (continued) 1 IMAGE CONTRAST . . . . . . . . The color balance of the image shifts green as the number increases and shifts to purple as the number decreases (displays only when the source is selected to VIDEO). · When the TV50 (PAL, SECAM) signal is inputted, you cannot adjust the TINT. Adjusts the color intensity of the image (displays only when the source is selected to VIDEO). Opt 2 INSTALLATION IMAGE REVERSE Use to reverse or invert the projected image. MIRROR INVERT is effective INSTALLATION when the projector is ceiling-mounted. If the image has KEYSTONE 0° keystone distortion, select the approximate setting. To select whether to boot up automatically when the power is turned on external to the projector. Use to select the length of time before projector switches to stand-by when there is no input signal selected source. [. . . ] · Adjust the angle of the projector to make a right angle to the screen. · · · · · · · Adjust the projecting distance. Clean lens. The image is turned off. · The air inlet grill, outlet grill or air filter is clogged with dust or some objects. (In this case, the TEMP indicator does not light up. ) The image is · The projector is not at a right angle to the screen. [. . . ]