User manual ACER PD520

[. . . ] English Table of Contents Usage Notice Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the screen displays "No Signal" , please make sure the signal cables are securely connected. If you connect multiple sources at the same time, use the "Source" button on the Remote Control or Panel Control to switch. Turn on the projector first and then the computer. 2 Power / Standby Lens cap 1 10 English Installation Powering Off the Projector 1. Press the "Power/Standby" button to turn off the projector lamp. After pressing the "Power/Standby" button, you will see a message "Power off the lamp?" on the on-screen display. If you want to turn on the projector, you must press the "Power/ Standby"button within 2 minutes of the start of the indicator flashing. Disconnect the power cord from the electrical outlet and the projector. Do not turn on the projector immediately following a power off procedure. When the "TEMP" indicator flashes red for about 10 seconds, you will see a message "Fan Fail" on the on-screen display. After 5 seconds, the "Power/Standby" indicator flashes green for about 2 minutes and the projector will automatically shut itself down. When the "TEMP" indicator lights solid red for about 10 seconds, it indicates the projector has been overheated. You will see a message "Over Temperature" on the on-screen display. After 5 seconds, the "Power/Standby" indicator flashes green for about 2 minutes and the projector will automatically shut itself down. When the "LAMP" indicator lights solid orange and "Power/ Standby" indicator flashes green for about 2 minutes. Please contact your local reseller or service center. 11 English Installation Adjusting the Projected Image Adjusting the Projector Height The projector is equipped with an elevator foot for adjusting the projector height. To raise the projector: 1. Raise the projector to the desired display angle , then release the button to lock the elevator foot into position. Lower down the projector, then release the button to lock the elevator foot into position. Use to fine-tune tilt-adjustment. 1 Elevator Button 2 Elevator Foot 3 12 English Installation Adjusting the Projector Zoom / Focus You may adjust zoom ring to zoom in / out. Rotate the zoom ring counter-clockwise to zoom in and clockwise to zoom out. The projector will focus at distances from 3. 74 feet to 39. 37 feet (1. 14m to 12m) Zoom Ring Focus Ring Adjusting Projection Image Size Max. The projector will save any change you made automatically. 16 English User Controls On-Screen Display Menus How to operate 4The Projector has multilingual On-Screen Display(OSD) menus that allow you to make image adjustments and change a variety of settings. The projector will detect the source automatically. 4To open the OSD menu, press the "Menu" button on the Remote Control or Panel Control. 4 When OSD is displayed, press E. g. : Image-I PIP Image-I. . . Language Management While making selection on a particular page, press "Enter" key to go into submenu. 4 Press by key to select the required item and adjust the settings key. When a specified item is selected, the color of the item will change from yellowish brown to blue. [. . . ] In the Windows Program Manager, click the "Windows Setup" icon in the Main group. Verify that your display resolution setting is less than or equal to 1024 x 768. Open "My Computer" icon, the "Control Panel" folder, and then double click the "Display" icon. Verify that the resolution setting is less than or equal to 1024 x 768 resolution. [. . . ]