User manual ACER PD115

[. . . ] Table of Contents Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Usage Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Under normal conditions, the projector can be switched on again after it has cooled down. If the problem persists, you should contact your local dealer or our service center. When the "TEMP" indicator flashs red for about 10 seconds, you will see a message "Fan fail. Lamp will automatically turn off soon. " on the on-screen display. 12 Installation Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with an elevator foot for adjusting the image height. To raise the image: 1. 4 Confirm your selection of items. Four Directional Select Keys 4 Use to select items or make adjustments to your selection. 15 . . . English User Controls Using the Remote Control Power 4 Refer to the "Power On/Off the Projector" section on pages 11-12. Empowering Key 4 Display the "Display Mode" submenu of the onscreen display menu to select display mode from PC, Vedio, Theatre and User directly. Menu 4 Press "Menu" to launch the on screen display menu. To exit OSD, press "Menu" again. Four Directional Select Keys 4 Use to select items or make adjustments to your selection. Laser Button 4 Aim the remote at the viewing screen, press and hold this button to activate the laser pointer. Zoom 4 Zoom in / out Keystone + / degrees). 4 Adjusts image distortion caused by tilting the projector (±16 Page Up (Computer mode only) 4 Use this button to page up. This function is only available Page Down (Computer mode only) when the projector is connected to a computer via an USB cable. 4 Use this button to page down. This function is only available Re-Sync when the projector is connected to a computer via an USB cable. 4 Automatically synchronizes the projector to the input source. Hide 4 Momentarily turns off the video. Press "Hide" to hide image, press again to restore display of the image. Source 4 Press "Source" to choose RGB, Component-p, Component-i, S-Video, Composite Video , DVI-D (Optional)and HDTV sources. Freeze 4 Press "Freeze" to pause the screen image. English . . . 16 User Controls On Screen Display Menus The Projector has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to operate 1. To open the OSD menu, press "Menu" on the Remote Control or press "Menu/Enter"on the Control Panel. 2. When OSD is displayed, use to enter sub menu for feature setting. keys to select any item in the main menu. Use settings by keys to select the desired item and adjust the key. 4. Select the next item to be adjusted in the sub menu and adjust as described above. 5. Press "Menu" on the Remote Control or press "Menu/Enter"on the Control Panel, the screen will return to the main menu. 6. To exit OSD, press "Menu" on the Remote Control or press "Menu/Enter"on the Control Panel again. The OSD menu will close and the projector will automatically save the new settings. Main Menu Sub Menu settings 17 . . . English User Controls Language (Computer / Video Mode) Language Choose the multilingual OSD menu . or key to select Press "Menu" on the Remote Control or press "Menu/Enter"on the Control Panel to finalize the selection. English . . . [. . . ] 4 Make sure the projection screen is between the required distance -3. 9 to 32. 8 feet (1. 2 to 10. 0 meters) from the projector. 29 . . . English Appendices Problem: The image is outstretched when displaying 16:9 DVD. The projector automatically detects 16:9 DVD and adjusts the aspect ratio by digitizing to full screen with 4:3 default setting. If the image is still outstretched, you will also need to adjust the aspect ratio by referring to the following: 4 Please select 4:3 aspect ratio type on your DVD player if you are playing a 16:9 DVD. 4 If you can't select 4:3 aspect ratio type on your DVD player, please select 4:3 aspect ratio in the on screen menu. Problem: Image is reversed. 4 Select "Management" from the OSD and adjust the projection direction. [. . . ]